FAQ Suggestions


Well, your lsmod command proves it's loaded. I don't off the top of my head know how to check it's actually in use though, short of issuing a 'sudo modprobe -r etnaviv' and then watching to see what falls over.
 
I just tried for the 1st time,
I do get an image but my Pyra keeps resetting to log-in
izxe_PNY_xTiC86klcD4aYPs35RXGVBYL2A3tF6O1c5WWDHXKGOJd3SqQyF908vjJUf4G2Gok4tRER6UOEFj2jFK-TpMZxDRs17hIBLFQvFiaZ8YGjhuXjub7ZZZrwcAu54z6ygAjEFLhT3dNg3kq8F9mhF8dke_F5Sicxf-CpjMCp1NtkQFmQP6nDjonCK3BN5IiuRO-8qdPvigMT4jKPSBf4BAdPqP_7IQfWp7xzldR1pNu1mAOgS5tvadMHPuFv9b1p48SJ2SFD0h3m3X8CNYnAd3v-bO9Ug2X5NTsHoOjIZVmBNXa42KreZF99kiR6X2YNurDT9xF3SSB7WCL1QO5mHlaYY6WYDsdv6iSbY3FGbS8L2uMuuWWN-eOdcVJTqLCHnSnGydaSu2zrqWZs2EI9P6682fd3XJ0imtid_zFqsGYGEPmwYbIazHewRZKa2237mxc8UYpms8BAJGB59XiqbOleUz-kErFumUdlBW1AIZt32DQy-wsnGInzf1_wPv9h9trmKJ16fEUWN4pvqqj3TMJ08VAT42pihU25X9nlbVf5WwbcuaC6-4_h-gTCnW7BojNSoR1Cihibm9f6FDNhbsawTJ9HyZMoRtQRGic80CjR6NRd__go68if6dchhalRGefs-oa-sLhbK18orUPWL4UNLTX_J4qaxw1FbVwvIb4NUHgKrcD_b8Wc8sYhvXbksCeTHGuMPNBKEtjqPR=w715-h1271-no
 
Hi all,

@levi : I tried this afternoon to remove the etnaviv module kernel but failed, because it's already in use.

@Eight Bit : Did you do something in particular to get HDMI out working ? All I get on my end is a white blinking cursor on the Pyra's screen, and absolutely nothing on the other monitor :D

Cheers, Magic Sam
 
Hi all,

@levi : I tried this afternoon to remove the etnaviv module kernel but failed, because it's already in use.

@Eight Bit : Did you do something in particular to get HDMI out working ? All I get on my end is a white blinking cursor on the Pyra's screen, and absolutely nothing on the other monitor :D

Cheers, Magic Sam
No, nothing... I was just logged in, plugged the HDMI in, then my session logged out and went back to log-in screen and the HDMI started output.
Logging back in with HDMI on results in directly logging off again, going back to the login screen again.

So... It's not usable yet :-/
 
Back
Top