Both full size USB ports not working

[Kazuki]

I've tried pluging in different stuff but nothing happens.
Here is dmesg from booting up with grep usb.

[ 0.000000] Kernel command line: root=PARTUUID=efca4260-02 console=ttyO2,115200n8 console=tty0 vram=12M omapfb.vram=0:8M,1:4M omapfb.rotate_type=0 omapdss.def_disp=lcd rootwait twl4030_charger.allow_usb=1 musb_hdrc.preserve_vbus=1 log_buf_len=8M ignore_loglevel earlyprintk drm_kms_helper.fbdev_rotation=8 drm.force_hw_rotation fastboot coherent_pool=1M twl4030_charger.allow_usb=1 fsck.repair=yes rootfstype=f2fs rootwait ignore_loglevel [ 0.311800] usbcore: registered new interface driver usbfs [ 0.311903] usbcore: registered new interface driver hub [ 0.312042] usbcore: registered new device driver usb [ 0.312316] usb_phy_generic hsusb2_phy: hsusb2_phy supply vcc not found, using dummy regulator [ 2.612370] usbcore: registered new interface driver usb-storage [ 2.883317] usbcore: registered new interface driver usbhid [ 2.889284] usbhid: USB HID core driver [ 3.526369] usb3503 0-0008: usb3503_probe [ 3.535705] usb3503 0-0008: reset gpio state 1 [ 3.540407] usb3503 0-0008: usb3503_connect [ 3.544852] usb3503 0-0008: usb3503_reset 1 [ 3.555758] usb3503 0-0008: SP_ILOCK failed (-121) [ 3.560822] usb3503 0-0008: usb3503_probe: probed in hub mode [ 4.507533] bq2429x_charger 1-006b: bq2429x_parse_dt,line=1539 chg_current = 2048000 usb_input_current = 3000000 adp_input_current = 2048000 bat_volt_max = 4200000 [ 6.877379] wwan_on_off_probe: onoff = 59cafd02 indicator = e3651999 -304228288 usb_phy = -1054427720 [ 8.399660] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.06 [ 8.413159] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.425844] usb usb1: Product: EHCI Host Controller [ 8.438338] usb usb1: Manufacturer: Linux 5.6.19-daveiii-pyradef-aufs ehci_hcd [ 8.450014] usb usb1: SerialNumber: 4a064c00.ehci [ 8.835964] usb 1-2: new high-speed USB device number 2 using ehci-omap [ 13.312134] usb usb1-port2: Cannot enable. Maybe the USB cable is bad? [ 17.785741] usb usb1-port2: Cannot enable. Maybe the USB cable is bad? [ 17.815737] usb usb1-port2: attempt power cycle

 

[elw3]

Was anything plugged in during that boot?

 

[Kazuki]

No nothing.

 

[Linux-SWAT]

Cross-linking:

OTG issue with a USB3 device

Hi all, I am a long time lurker and a very proud owner of a Pyra. I am trying to get a USB3 storage device (Samsung ssd) working with the Pyra using a USB OTG cable and cannot get it to work. The device works when plugged directly into the Pyra USB2 port. Also, it works fine using the same...

pyra-handheld.com

 

[EvilDragon]

That seems to happen sometimes - I think it's also the reason the modem does not always appear!
I know I had one U-Boot version where this always happened... we switched a few times, so I'm not sure which one is on your unit (maybe we had the bad one installed at some time?)

Usually, if this fails, it won't work again before you restart the unit.

 

[Kazuki]

Tried restarting it but it still gives error. The other USB port works the micro USB 3.0. the esata adaptor works but I can't test got wrong cable it has different connector.

--Edit--

Turning it on today I saw the USB ports were working. But after turning it off and back on again they stopped working. It seems to randomly work or not work.
[ 0.000000] Kernel command line: root=PARTUUID=efca4260-02 console=ttyO2,115200n8 console=tty0 vram=12M omapfb.vram=0:8M,1:4M omapfb.rotate_type=0 omapdss.def_disp=lcd rootwait twl4030_charger.allow_usb=1 musb_hdrc.preserve_vbus=1 log_buf_len=8M ignore_loglevel earlyprintk drm_kms_helper.fbdev_rotation=8 drm.force_hw_rotation fastboot coherent_pool=1M twl4030_charger.allow_usb=1 fsck.repair=yes rootfstype=f2fs rootwait ignore_loglevel [ 0.300575] usbcore: registered new interface driver usbfs [ 0.300627] usbcore: registered new interface driver hub [ 0.301132] usbcore: registered new device driver usb [ 0.301451] usb_phy_generic hsusb2_phy: hsusb2_phy supply vcc not found, using dummy regulator [ 2.606138] usbcore: registered new interface driver usb-storage [ 2.883533] usbcore: registered new interface driver usbhid [ 2.889463] usbhid: USB HID core driver [ 3.520495] usb3503 0-0008: usb3503_probe [ 3.534882] usb3503 0-0008: reset gpio state 1 [ 3.539610] usb3503 0-0008: usb3503_connect [ 3.544022] usb3503 0-0008: usb3503_reset 1 [ 3.554930] usb3503 0-0008: SP_ILOCK failed (-121) [ 3.559996] usb3503 0-0008: usb3503_probe: probed in hub mode [ 4.498985] bq2429x_charger 1-006b: bq2429x_parse_dt,line=1539 chg_current = 2048000 usb_input_current = 3000000 adp_input_current = 2048000 bat_volt_max = 4200000 [ 6.842344] wwan_on_off_probe: onoff = fdd965a5 indicator = ab187257 -307996608 usb_phy = -1054427720 [ 8.257383] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.06 [ 8.270227] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 8.281739] usb usb1: Product: EHCI Host Controller [ 8.290647] usb usb1: Manufacturer: Linux 5.6.19-daveiii-pyradef-aufs ehci_hcd [ 8.302183] usb usb1: SerialNumber: 4a064c00.ehci [ 8.695369] usb 1-2: new high-speed USB device number 2 using ehci-omap [ 8.916327] usb 1-2: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1.a0 [ 8.936376] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 34.874953] usb 1-2.3: new high-speed USB device number 3 using ehci-omap [ 35.036668] usb 1-2.3: New USB device found, idVendor=1e2d, idProduct=0061, bcdDevice= 2.32 [ 35.051865] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 35.066270] usb 1-2.3: Product: LTE Modem [ 35.071592] usb 1-2.3: Manufacturer: Cinterion [ 35.641689] cdc_ether 1-2.3:1.10 wwan0: register 'cdc_ether' at usb-4a064c00.ehci-2.3, Mobile Broadband Network Device, de:ad:be:ef:00:00 [ 35.717067] cdc_ether 1-2.3:1.12 wwan1: register 'cdc_ether' at usb-4a064c00.ehci-2.3, Mobile Broadband Network Device, de:ad:be:ef:00:01 [ 35.766438] usbcore: registered new interface driver cdc_ether [ 35.866628] usbcore: registered new interface driver cdc_acm

--Edit--
Did some more test and it looks like the 4g Modem stops working when the USB ports are dead.

 

[Kazuki]

Tried reflashing os with https://packages.pyra-handheld.com/rootfs/buster/pyra-38-install.img.7z
But that did not fix it still sometimes boots with USB and 4g modem broken.

Also the system won't reboot everything seems to turn off but nothing happens.
If I try to push the power button nothing happens.
I have to pull out battery and put back in then it boots back up.

 

[EvilDragon]

Yes, that's what I've written in my post. There is some bug that causes the USB ports not to work sometimes. That's some weird software issue.

A reboot does not work on our current OS. There's a fix already but not yet implemented.
Always power down and switch it on again.

 

[EvilDragon]

Can you post a dmesg when the ports are not working? That should give us a clue why this happens.

 

[Kazuki]

Here is the dmesg

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.6.19-daveiii-pyradef-aufs (pyra@debian-buster) (gcc version 8.3.0 (Debian 8.3.0-2)) #3 SMP PREEMPT Mon Dec 14 18:23:52 CET 2020
[    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: Pyra-Handheld-V5.3
[    0.000000] printk: debug: ignoring loglevel setting.
[    0.000000] printk: debug: ignoring loglevel setting.
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 64 MiB at 0x00000000fb000000
[    0.000000] OMAP4: Map 0x00000000afd00000 to (ptrval) for dram barrier
[    0.000000] On node 0 totalpages: 1043712
[    0.000000]   DMA zone: 2295 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 195840 pages, LIFO batch:63
[    0.000000]   HighMem zone: 847872 pages, LIFO batch:63
[    0.000000] OMAP5432 ES2.0
[    0.000000] percpu: Embedded 20 pages/cpu s50316 r8192 d23412 u81920
[    0.000000] pcpu-alloc: s50316 r8192 d23412 u81920 alloc=20*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1041417
[    0.000000] Kernel command line: root=PARTUUID=094c7470-02 console=ttyO2,115200n8 console=tty0 vram=12M omapfb.vram=0:8M,1:4M omapfb.rotate_type=0 omapdss.def_disp=lcd rootwait twl4030_charger.allow_usb=1 musb_hdrc.preserve_vbus=1 log_buf_len=8M ignore_loglevel earlyprintk drm_kms_helper.fbdev_rotation=8 drm.force_hw_rotation fastboot coherent_pool=1M twl4030_charger.allow_usb=1 fsck.repair=yes rootfstype=f2fs  rootwait ignore_loglevel
[    0.000000] printk: log_buf_len: 8388608 bytes
[    0.000000] printk: early log buf free: 63724(97%)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: mapped [mem 0xa53bf000-0xa93bf000] (64MB)
[    0.000000] Memory: 3948708K/4174848K available (10478K kernel code, 908K rwdata, 2772K rodata, 2048K init, 269K bss, 160604K reserved, 65536K cma-reserved, 3325952K highmem)
[    0.000000] random: get_random_u32 called from __kmem_cache_create+0x34/0x4f8 with crng_init=0
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000]     Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] OMAP clockevent source: timer1 at 32768 Hz
[    0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16ac02862, max_idle_ns: 440795202218 ns
[    0.000010] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511085ns
[    0.000033] Switching to timer-based delay loop, resolution 162ns
[    0.000168] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[    0.000183] OMAP clocksource: 32k_counter at 32768 Hz
[    0.002028] Console: colour dummy device 80x30
[    0.002990] printk: console [tty0] enabled
[    0.003061] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.28 BogoMIPS (lpj=61440)
[    0.003111] pid_max: default: 32768 minimum: 301
[    0.003399] LSM: Security Framework initializing
[    0.003531] Yama: becoming mindful.
[    0.003713] AppArmor: AppArmor initialized
[    0.003753] TOMOYO Linux initialized
[    0.003872] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.003920] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.005197] CPU: Testing write buffer coherency: ok
[    0.005284] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.005743] /cpus/cpu@0 missing clock-frequency property
[    0.005803] /cpus/cpu@1 missing clock-frequency property
[    0.005838] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.059701] Setting up static identity map for 0x80200000 - 0x80200060
[    0.079705] rcu: Hierarchical SRCU implementation.
[    0.119746] smp: Bringing up secondary CPUs ...
[    0.200083] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.200097] CPU1: Spectre v2: using ICIALLU workaround
[    0.200228] smp: Brought up 1 node, 2 CPUs
[    0.200242] SMP: Total of 2 processors activated (24.57 BogoMIPS).
[    0.200259] CPU: All CPU(s) started in HYP mode.
[    0.200267] CPU: Virtualization extensions available.
[    0.200709] devtmpfs: initialized
[    0.215001] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.215456] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.215487] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.216799] pinctrl core: initialized pinctrl subsystem
[    0.217623] thermal_sys: Registered thermal governor 'fair_share'
[    0.217623] thermal_sys: Registered thermal governor 'step_wise'
[    0.217645] thermal_sys: Registered thermal governor 'user_space'
[    0.218508] NET: Registered protocol family 16
[    0.221031] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.222018] omap_hwmod: l3_main_3 using broken dt data from ocp
[    0.222842] omap_hwmod: l3_main_2 using broken dt data from ocp
[    0.235873] audit: initializing netlink subsys (disabled)
[    0.236553] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1
[    0.239962] cpuidle: using governor menu
[    0.262986] platform 50000000.gpmc: Cannot lookup hwmod 'gpmc'
[    0.263186] omap-gpmc 50000000.gpmc: _od_fail_runtime_resume: FIXME: missing hwmod/omap_dev info
[    0.263216] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[    0.271944] No ATAGs?
[    0.272006] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.272039] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.294772] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.301025] vsys_cobra: supplied by vmain
[    0.305245] iommu: Default domain type: Translated 
[    0.307436] vgaarb: loaded
[    0.308138] SCSI subsystem initialized
[    0.308454] libata version 3.00 loaded.
[    0.308962] usbcore: registered new interface driver usbfs
[    0.309054] usbcore: registered new interface driver hub
[    0.309176] usbcore: registered new device driver usb
[    0.309451] usb_phy_generic hsusb2_phy: hsusb2_phy supply vcc not found, using dummy regulator
[    0.311914] Advanced Linux Sound Architecture Driver Initialized.
[    0.312655] NetLabel: Initializing
[    0.312681] NetLabel:  domain hash size = 128
[    0.312685] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.312746] NetLabel:  unlabeled traffic allowed by default
[    0.313964] clocksource: Switched to clocksource arch_sys_counter
[    0.379728] VFS: Disk quotas dquot_6.6.0
[    0.379794] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.380423] AppArmor: AppArmor Filesystem Enabled
[    0.391584] NET: Registered protocol family 2
[    0.392091] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.392123] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.392201] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.392336] TCP: Hash tables configured (established 8192 bind 8192)
[    0.392442] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.392489] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.392702] NET: Registered protocol family 1
[    0.393159] PCI: CLS 0 bytes, default 64
[    0.393618] Trying to unpack rootfs image as initramfs...
[    1.245211] Freeing initrd memory: 18612K
[    1.245730] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[    1.245913] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    1.248293] Initialise system trusted keyrings
[    1.248441] workingset: timestamp_bits=14 max_order=20 bucket_order=6
[    1.258670] zbud: loaded
[    1.265670] jitterentropy: Initialization failed with host not compliant with requirements: 2
[    1.265691] Key type asymmetric registered
[    1.265719] Asymmetric key parser 'x509' registered
[    1.265756] bounce: pool size: 64 pages
[    1.265861] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    1.265875] io scheduler mq-deadline registered
[    1.265902] io scheduler kyber registered
[    1.271590] OMAP GPIO hardware version 0.1
[    1.296242] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
[    1.369296] GPIO line 74 (gpio8_234/msecure) hogged as output/high
[    1.397301] ti-pipe3 4a096000.phy: can't get syscon-pllreset, sata dpll won't idle
[    1.398837] pinctrl-single 4ae0c840.pinmux: 30 pins, size 60
[    1.399500] pinctrl-single 4a002840.pinmux: 219 pins, size 438
[    1.403644] pwm-backlight keyboard-backlight: keyboard-backlight supply power not found, using dummy regulator
[    1.403983] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    1.408917] ti_abb 4ae07cdc.regulator-abb-mpu: can't request region for resource [mem 0x4ae07cdc-0x4ae07ce3]
[    1.408956] ti_abb: probe of 4ae07cdc.regulator-abb-mpu failed with error -16
[    1.409018] ti_abb 4ae07ce4.regulator-abb-mm: can't request region for resource [mem 0x4ae07ce4-0x4ae07ceb]
[    1.409043] ti_abb: probe of 4ae07ce4.regulator-abb-mm failed with error -16
[    1.409504] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.412231] 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 108, base_baud = 3000000) is a OMAP UART2
[    2.371633] printk: console [ttyO2] enabled
[    2.376742] omap_uart 48068000.serial: no wakeirq for uart5
[    2.382784] 48068000.serial: ttyO5 at MMIO 0x48068000 (irq = 121, base_baud = 3000000) is a OMAP UART5
[    2.393282] omap_uart 4806c000.serial: no wakeirq for uart1
[    2.399342] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 122, base_baud = 3000000) is a OMAP UART1
[    2.409426] serial serial0: tty port ttyO1 registered
[    2.414971] omap_uart 4806e000.serial: no wakeirq for uart3
[    2.421023] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 123, base_baud = 3000000) is a OMAP UART3
[    2.432783] omap_rng 48090000.rng: Random Number Generator ver. 20
[    2.433321] random: fast init done
[    2.440099] omapdss_dss 58000000.dss: 58000000.dss supply vdda_video not found, using dummy regulator
[    2.443037] random: crng init done
[    2.456546] DSS: OMAP DSS rev 6.1
[    2.473921] brd: module loaded
[    2.482080] loop: module loaded
[    2.485445] wwan_on_off_init: wwan_on_off_init
[    2.490538] wwan_on_off_probe: wwan_on_off_probe()
[    2.497958] ahci 4a140000.sata: 4a140000.sata supply ahci not found, using dummy regulator
[    2.506777] ahci 4a140000.sata: 4a140000.sata supply phy not found, using dummy regulator
[    2.515536] ahci 4a140000.sata: 4a140000.sata supply target not found, using dummy regulator
[    2.524637] ahci 4a140000.sata: SSS flag set, parallel bus scan disabled
[    2.531741] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    2.540751] ahci 4a140000.sata: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part ccc apst 
[    2.551669] scsi host0: ahci
[    2.555178] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 31
[    2.564140] mtdoops: mtd device (mtddev=name/number) must be supplied
[    2.572787] libphy: Fixed MDIO Bus: probed
[    2.580660] omap-dwc3 4a020000.omap_dwc3: vbus init failed
[    2.586772] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.593691] ehci-pci: EHCI PCI platform driver
[    2.598476] usbcore: registered new interface driver usb-storage
[    2.605414] mousedev: PS/2 mouse device common for all mice
[    2.612856] i2c /dev entries driver
[    2.616640] IR NEC protocol handler initialized
[    2.621419] IR RC5(x/sz) protocol handler initialized
[    2.626796] IR RC6 protocol handler initialized
[    2.631581] IR JVC protocol handler initialized
[    2.636385] IR Sony protocol handler initialized
[    2.641255] IR SANYO protocol handler initialized
[    2.646259] IR Sharp protocol handler initialized
[    2.651234] IR MCE Keyboard/mouse protocol handler initialized
[    2.657412] IR XMP protocol handler initialized
[    2.662189] Driver for 1-wire Dallas network protocol.
[    2.671359] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    2.680935] sdhci: Secure Digital Host Controller Interface driver
[    2.687499] sdhci: Copyright(c) Pierre Ossman
[    2.693026] omap_gpio 48053000.gpio: Could not set line 4 debounce to 200000 microseconds (-22)
[    2.702212] omap_hsmmc 4809c000.mmc: Got CD GPIO
[    2.707125] omap_hsmmc 4809c000.mmc: Got WP GPIO
[    2.750338] omap_gpio 48057000.gpio: Could not set line 13 debounce to 200000 microseconds (-22)
[    2.759745] omap_hsmmc 480d1000.mmc: Got CD GPIO
[    2.764712] omap_hsmmc 480d1000.mmc: Got WP GPIO
[    2.774382] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.781191] txs02612 txs02612: probe
[    2.785159] txs02612 txs02612: failed to get mmc phandle in /txs02612 node
[    2.792452] txs02612 txs02612: could not get access to host port, using manual mode
[    2.823981] txs02612_request: current=1 client=0
[    2.854049] txs02612 txs02612: probed
[    2.858064] txs02612_request: current=0 client=1
[    2.862978] ledtrig-cpu: registered to indicate activity on CPUs
[    2.871709] usbcore: registered new interface driver usbhid
[    2.877688] usbhid: USB HID core driver
[    2.881942] ashmem: initialized
[    2.890791] oprofile: using timer interrupt.
[    2.895475] drop_monitor: Initializing network drop monitor service
[    2.895509] ata1: SATA link down (SStatus 0 SControl 300)
[    2.902759] NET: Registered protocol family 10
[    2.939455] Segment Routing with IPv6
[    2.943423] mip6: Mobile IPv6
[    2.946620] NET: Registered protocol family 17
[    2.951327] mpls_gso: MPLS GSO support
[    2.955679] ThumbEE CPU extension supported.
[    2.960205] Registering SWP/SWPB emulation handler
[    2.965364] omap_vc_init_channel: No PMIC info for vdd_core
[    2.971244] omap_vp_init: No PMIC info for vdd_core
[    2.976443] omap_vc_init_channel: No PMIC info for vdd_mm
[    2.982137] omap_vp_init: No PMIC info for vdd_mm
[    2.987140] omap_vc_init_channel: No PMIC info for vdd_mpu
[    2.992940] omap_vp_init: No PMIC info for vdd_mpu
[    2.998041] Power Management for TI OMAP4+ devices.
[    3.003858] Loading compiled-in X.509 certificates
[    3.012911] Loaded X.509 cert 'Build time autogenerated kernel key: 4020818a539cdd7ae890874388bde6caf4fc6257'
[    3.023896] Key type ._fscrypt registered
[    3.028145] Key type .fscrypt registered
[    3.032277] Key type fscrypt-provisioning registered
[    3.037814] AppArmor: AppArmor sha1 policy hashing enabled
[    3.064791] dmm 4e000000.dmm: initialized all PAT entries
[    3.074404] omap-iommu 4a066000.mmu: 4a066000.mmu registered
[    3.082287] bmc150_accel_i2c 2-0010: mounting matrix not found: using identity...
[    3.117617] bmc150_accel_i2c 2-0010: Error: Reading chip id
[    3.123568] bmc150_accel_i2c: probe of 2-0010 failed with error -121
[    3.130770] bmc150_magn_i2c 2-0012: mounting matrix not found: using identity...
[    3.138857] bmc150_magn_i2c 2-0012: Failed to bring up device from suspend mode
[    3.146724] bmc150_magn_i2c: probe of 2-0012 failed with error -121
[    3.153749] bmp280 2-0077: 2-0077 supply vddd not found, using dummy regulator
[    3.161440] bmp280 2-0077: 2-0077 supply vdda not found, using dummy regulator
[    3.180117] bmp280: probe of 2-0077 failed with error -121
[    3.186312] bmp280 2-0076: 2-0076 supply vddd not found, using dummy regulator
[    3.193988] bmp280 2-0076: 2-0076 supply vdda not found, using dummy regulator
[    3.214610] bno055 2-0029: mounting matrix not found: using identity...
[    3.230069] bno055 2-0029: software revision id 0311
[    3.238013] input: iio-bridge: bno055 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48060000.target-module/48060000.i2c/i2c-2/2-0029/iio:device1/input/input0
[    3.257388] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz
[    3.264651] palmas 0-0048: Irq flag is 0x00000008
[    3.300694] palmas 0-0048: Muxing GPIO 3, PWM 0, LED 0
[    3.317925] palmas-rtc 48070000.i2c:palmas@48:rtc: registered as rtc0
[    3.330842] SMPS123: supplied by regulator-dummy
[    3.338335] SMPS45: supplied by regulator-dummy
[    3.345219] SMPS6: supplied by vsys_cobra
[    3.352046] SMPS7: supplied by vsys_cobra
[    3.358215] SMPS8: supplied by vsys_cobra
[    3.363924] SMPS9: supplied by vsys_cobra
[    3.368349] smps9: Bringing 0uV into 2100000-2100000uV
[    3.375094] SMPS10_OUT2: supplied by regulator-dummy
[    3.381991] SMPS10_OUT1: supplied by regulator-dummy
[    3.388341] LDO1: supplied by vsys_cobra
[    3.392672] ldo1: Bringing 0uV into 1800000-1800000uV
[    3.401381] LDO2: supplied by vsys_cobra
[    3.405947] ldo2: Bringing 0uV into 1800000-1800000uV
[    3.416415] ldo4: Bringing 0uV into 1800000-1800000uV
[    3.424026] LDO5: supplied by vsys_cobra
[    3.432803] LDO7: supplied by vsys_cobra
[    3.437417] ldo7: Bringing 0uV into 2000000-2000000uV
[    3.445074] LDO8: supplied by vsys_cobra
[    3.452395] LDO9: supplied by vmmcsd_fixed
[    3.460909] LDOLN: supplied by vsys_cobra
[    3.466982] LDOUSB: supplied by vsys_cobra
[    3.475779] palmas_pwrbutton 48070000.i2c:palmas@48:palmas_power_button: h/w controlled shutdown duration=8 seconds
[    3.490221] input: palmas_pwron as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48070000.target-module/48070000.i2c/i2c-0/0-0048/48070000.i2c:palmas@48:palmas_power_button/input/input1
[    3.516720] usb3503 0-0008: usb3503_probe
[    3.524325] usb3503 0-0008: reset gpio state 1
[    3.529012] usb3503 0-0008: usb3503_connect
[    3.533440] usb3503 0-0008: usb3503_reset 1
[    3.544589] usb3503 0-0008: SP_ILOCK failed (-121)
[    3.549674] usb3503 0-0008: usb3503_probe: probed in hub mode
[    3.556185] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
[    3.585024] as5013 1-0040: ID code: 0c
[    3.589632] as5013 1-0040: ID version: 0d
[    3.594392] as5013 1-0040: silicon revision: 00
[    3.599825] as5013 1-0040: control: f1
[    3.604006] input: nub0 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48072000.target-module/48072000.i2c/i2c-1/1-0040/input/input2
[    3.620791] as5013 1-0040: probe 40, gpio -2, irq 0, "as5013"
[    3.627874] as5013 1-0041: ID code: 0c
[    3.632357] as5013 1-0041: ID version: 0d
[    3.637057] as5013 1-0041: silicon revision: 00
[    3.642489] as5013 1-0041: control: f1
[    3.646632] input: nub1 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48072000.target-module/48072000.i2c/i2c-1/1-0041/input/input3
[    3.663454] as5013 1-0041: probe 41, gpio -2, irq 0, "as5013"
[    3.672860] input: tca8418 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48072000.target-module/48072000.i2c/i2c-1/1-0034/input/input4
[    3.690421] bq27xxx_battery_setup
[    3.693935] bq27xxx_battery_setup: dm_regs=12fa15bf
[    3.699633] bq27xxx_battery_settings
[    3.703432] bq27xxx_battery_set_config
[    3.707418] bq27xxx_battery_unseal
[    3.721682] bq27xxx_battery_update_dm_block
[    3.726126] bq27xxx-battery 1-0055: design-capacity has 6000
[    3.732106] bq27xxx_battery_update_dm_block
[    3.736544] bq27xxx-battery 1-0055: design-energy has 22200
[    3.742415] bq27xxx_battery_update_dm_block
[    3.746868] bq27xxx-battery 1-0055: terminate-voltage has 3200
[    3.753036] bq27xxx_battery_seal
[    3.764278] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
[    3.795382] input: TSC2007 Touchscreen as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/4807a000.target-module/4807a000.i2c/i2c-3/3-0048/input/input5
[    3.817038] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
[    3.824892] vdds_1v8_main: supplied by smps7
[    3.830202] pca953x 4-0022: using AI
[    3.860018] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz
[    3.868633] omap-iommu 55082000.mmu: 55082000.mmu registered
[    3.876406] pwm-backlight keyboard-backlight: keyboard-backlight supply power not found, using dummy regulator
[    3.887362] dmtimer posted=0
[    3.890775] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    3.900393] ldo4: supplied by vdds_1v8_main
[    3.911259] wwan_on_off_probe: wwan_on_off_probe()
[    3.917529] omap-dwc3 4a020000.omap_dwc3: vbus init failed
[    3.926882] omap_gpio 48053000.gpio: Could not set line 4 debounce to 200000 microseconds (-22)
[    3.936089] omap_hsmmc 4809c000.mmc: Got CD GPIO
[    3.940981] omap_hsmmc 4809c000.mmc: Got WP GPIO
[    3.980135] omap_hsmmc 480ad000.mmc: allocated mmc-pwrseq
[    4.064943] mmc3: new high speed SDXC card at address aaaa
[    4.072777] mmcblk3: mmc3:aaaa SF256 238 GiB 
[    4.082491]  mmcblk3: p1
[    4.104159] omap_gpio 48057000.gpio: Could not set line 13 debounce to 200000 microseconds (-22)
[    4.113448] omap_hsmmc 480d1000.mmc: Got CD GPIO
[    4.118380] omap_hsmmc 480d1000.mmc: Got WP GPIO
[    4.129946] omap_hsmmc 480ad000.mmc: card claims to support voltages below defined range
[    4.161898] mmc4: new high speed SDIO card at address 0001
[    4.244875] ldo3: supplied by vdds_1v8_main
[    4.249453] ldo6: supplied by vdds_1v8_main
[    4.448275] mmc5: new high speed SDXC card at address aaaa
[    4.457797] mmcblk5: mmc5:aaaa SF256 238 GiB 
[    4.467906]  mmcblk5: p1
[    4.472170] bq2429x_charger 1-006b: bq2429x_parse_dt,line=1539 chg_current = 2048000 usb_input_current = 3000000 adp_input_current = 2048000 bat_volt_max = 4200000
[    4.487673] bq2429x_charger 1-006b: found regulator-max-microvolt = 4200000
[    4.497744] vsys: Bringing 3300000uV into 3500000-3500000uV
[    4.507530] omapdss_dss 58000000.dss: bound 58001000.dispc (ops 0xc0ca350c)
[    4.514970] omapdss_dss 58000000.dss: bound 58004000.encoder (ops 0xc0ca52d4)
[    4.523287] omap-hdmi-audio omap-hdmi-audio.1.auto: snd-soc-dummy-dai <-> 58040000.encoder mapping ok
[    4.533327] omapdss_dss 58000000.dss: bound 58040000.encoder (ops 0xc0ca6160)
[    4.542350] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    4.549349] [drm] No driver support for vblank timestamp query.
[    4.587442] drm_setup_crtcs_fb: sw_rotations=1
[    4.592155] drm_setup_crtcs_fb: fbcon_rotate_hint=0
[    4.603854] ------------[ cut here ]------------
[    4.603854] WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x254/0x374
[    4.603862] 44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4WAKEUP (Idle): Data Access in User mode during Functional access
[    4.603867] Modules linked in:
[    4.603882] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.19-daveiii-pyradef-aufs #3
[    4.603884] Hardware name: Generic OMAP5 (Flattened Device Tree)
[    4.603888] [<c0212e60>] (unwind_backtrace) from [<c020d1a0>] (show_stack+0x10/0x14)
[    4.603904] [<c020d1a0>] (show_stack) from [<c0c1b544>] (dump_stack+0x94/0xa8)
[    4.603915] [<c0c1b544>] (dump_stack) from [<c02351f0>] (__warn+0xd0/0xf8)
[    4.603915] [<c02351f0>] (__warn) from [<c02355e0>] (warn_slowpath_fmt+0x94/0xb8)
[    4.603922] [<c02355e0>] (warn_slowpath_fmt) from [<c064c23c>] (l3_interrupt_handler+0x254/0x374)
[    4.603939] [<c064c23c>] (l3_interrupt_handler) from [<c0290864>] (__handle_irq_event_percpu+0x58/0x29c)
[    4.603945] [<c0290864>] (__handle_irq_event_percpu) from [<c0290ad4>] (handle_irq_event_percpu+0x2c/0x80)
[    4.603945] [<c0290ad4>] (handle_irq_event_percpu) from [<c0290b60>] (handle_irq_event+0x38/0x5c)
[    4.603948] [<c0290b60>] (handle_irq_event) from [<c02950f4>] (handle_fasteoi_irq+0xb8/0x168)
[    4.603988] [<c02950f4>] (handle_fasteoi_irq) from [<c028fae4>] (generic_handle_irq+0x24/0x34)
[    4.604006] [<c028fae4>] (generic_handle_irq) from [<c02900b8>] (__handle_domain_irq+0x5c/0xb4)
[    4.604015] [<c02900b8>] (__handle_domain_irq) from [<c064a570>] (gic_handle_irq+0x3c/0x78)
[    4.604037] [<c064a570>] (gic_handle_irq) from [<c0201ab8>] (__irq_svc+0x58/0x8c)
[    4.604037] Exception stack(0xc1201eb8 to 0xc1201f00)
[    4.604039] 1ea0:                                                       00000000 00000001
[    4.604048] 1ec0: 2ec1b000 00000000 c120a168 c120a158 efc95a78 00000000 00000000 12690b17
[    4.604056] 1ee0: 00000001 00000001 fffffff5 c1201f08 c08ff5a0 c08ff5c4 600c0013 ffffffff
[    4.604067] [<c0201ab8>] (__irq_svc) from [<c08ff5c4>] (cpuidle_enter_state+0x164/0x5b8)
[    4.604067] [<c08ff5c4>] (cpuidle_enter_state) from [<c08ffa54>] (cpuidle_enter+0x28/0x38)
[    4.604072] [<c08ffa54>] (cpuidle_enter) from [<c026781c>] (do_idle+0x234/0x29c)
[    4.604087] [<c026781c>] (do_idle) from [<c0267b78>] (cpu_startup_entry+0x18/0x20)
[    4.604098] [<c0267b78>] (cpu_startup_entry) from [<c100137c>] (start_kernel+0x7cc/0x810)
[    4.604098] [<c100137c>] (start_kernel) from [<00000000>] (0x0)
[    4.604098] ---[ end trace faada44a88fe9901 ]---
[    4.784701] dmtimer posted=0
[    4.852310] Console: switching to colour frame buffer device 160x45
[    5.497192] omapdrm omapdrm.0: fb0: omapdrmdrmfb frame buffer device
[    5.524184] [drm] Initialized omapdrm 1.0.0 20110917 for omapdrm.0 on minor 0
[    5.537966] wwan_on_off_probe: wwan_on_off_probe()
[    5.549008] modem_vbus_hdmi_power: supplied by vsys
[    5.559878] modem_vbus_power: supplied by modem_vbus_hdmi_power
[    5.572131] wwan_on_off_probe: onoff = 99ee7faa indicator = 74aecb90 -306037184 usb_phy = -1054427720
[    5.587679] wwan_on_off_probe: wwan_on_off_probe() wwan=5d3bcb5c
[    5.599703] wwan_on_off_is_powered_on: gpio value = 0
[    5.610833] wwan_on_off_is_powered_on: return 'false'
[    5.622010] wwan_on_off_rfkill_set_block: blocked: 1
[    5.632784] wwan_on_off_set_power:on = 0
[    5.642397] wwan_on_off_is_powered_on: gpio value = 0
[    5.653109] wwan_on_off_is_powered_on: return 'false'
[    5.663760] wwan_on_off_set_power: state 0
[    5.673068] wwan_on_off_set_power: regulator 0
[    5.682894] wwan_on_off_set_power: done
[    5.691931] wwan_on_off_probe: successfully probed
[    5.702635] otg_path: supplied by otg
[    5.712073] dwc3 4a030000.dwc3: Failed to get clk 'ref': -2
[    5.724001] dwc3 4a030000.dwc3: changing max_speed on rev 5533202a
[    5.737460] input: user-buttons as /devices/platform/user-buttons/input/input6
[    5.753581] input: pyra-game-buttons as /devices/platform/pyra-game-buttons/input/input7
[    5.770724] input: pyra-lid-wakeup as /devices/platform/pyra-lid-wakeup/input/input8
[    5.787966] palmas-rtc 48070000.i2c:palmas@48:rtc: setting system clock to 2021-06-09T08:44:10 UTC (1623228250)
[    5.803566] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    5.817660] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    5.829236] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    5.848330] l4sec_cm:clk:0038:0: failed to disable
[    5.858004] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db
[    5.858079] ALSA device list:
[    5.878542]   #0: HDMI 58040000.encoder
[    5.888613] Freeing unused kernel memory: 2048K
[    5.934847] Run /init as init process
[    5.964741]   with arguments:
[    5.993349]     /init
[    6.020693]     earlyprintk
[    6.048220]     fastboot
[    6.074818]   with environment:
[    6.101940]     HOME=/
[    6.101962]     TERM=linux
[    6.153231]     vram=12M
[    6.270419] set_switch() to 0
[    6.564101] drm_setup_crtcs_fb: sw_rotations=1
[    6.573320] drm_setup_crtcs_fb: fbcon_rotate_hint=0
[    6.872388] ehci-omap: OMAP-EHCI Host Controller driver
[    6.898775] mmc0: new high speed MMC card at address 0001
[    6.920662] mmcblk0: mmc0:0001 HBG4a2 29.1 GiB 
[    6.933627] mmcblk0boot0: mmc0:0001 HBG4a2 partition 1 4.00 MiB
[    6.948400] mmcblk0boot1: mmc0:0001 HBG4a2 partition 2 4.00 MiB
[    6.962375] mmcblk0rpmb: mmc0:0001 HBG4a2 partition 3 4.00 MiB, chardev (245:0)
[    6.977057]  mmcblk0: p1 p2
[    7.021151] etnaviv etnaviv: bound 59000000.bb2d (ops gpu_ops [etnaviv])
[    7.033480] pvrsrvkm 56000000.gpu: Enabling quirks 00000000
[    7.044283] [drm] Initialized pvr 1.14.3699939 20110701 for 56000000.gpu on minor 2
[    7.048752] cfg80211: failed to load regulatory.db
[    7.065890] etnaviv-gpu 59000000.bb2d: model: GC320, revision: 5301
[    7.077883] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1
[    7.084037] ehci-omap 4a064c00.ehci: EHCI Host Controller
[    7.100253] ehci-omap 4a064c00.ehci: new USB bus registered, assigned bus number 1
[    7.114047] ehci-omap 4a064c00.ehci: irq 106, io mem 0x4a064c00
[    7.154177] ehci-omap 4a064c00.ehci: USB 2.0 started, EHCI 1.00
[    7.170718] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.06
[    7.183576] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.195528] usb usb1: Product: EHCI Host Controller
[    7.204562] usb usb1: Manufacturer: Linux 5.6.19-daveiii-pyradef-aufs ehci_hcd
[    7.216372] usb usb1: SerialNumber: 4a064c00.ehci
[    7.225588] hub 1-0:1.0: USB hub found
[    7.233218] hub 1-0:1.0: 3 ports detected
[    7.604098] usb 1-2: new high-speed USB device number 2 using ehci-omap
[    7.706183] ehci-omap 4a064c00.ehci: port 2 reset error -110
[    8.023348] process '/usr/bin/fstype' started with executable stack
[    8.119082] F2FS-fs (mmcblk0p2): recover fsync data on readonly fs
[    8.184366] F2FS-fs (mmcblk0p2): Mounted with checkpoint version = 69ac8889
[    8.401465] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist.
[    8.705843] ehci-omap 4a064c00.ehci: port 2 reset error -110
[    8.747624] systemd[1]: Inserted module 'autofs4'
[    8.791110] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    8.828854] systemd[1]: Detected architecture arm.
[    8.910243] systemd[1]: Set hostname to <pyra-handheld>.
[    9.196383] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[    9.225375] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[    9.402880] systemd[1]: /lib/systemd/system/dbpd.service:6: PIDFile= references path below legacy directory /var/run/, updating /var/run/dbpd.pid → /run/dbpd.pid; please update the unit file accordingly.
[    9.472594] systemd[1]: Listening on Journal Socket.
[    9.484835] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[    9.507449] systemd[1]: Reached target User and Group Name Lookups.
[    9.526073] systemd[1]: Listening on Journal Socket (/dev/log).
[    9.605554] ehci-omap 4a064c00.ehci: port 2 reset error -110
[    9.818423] RPC: Registered named UNIX socket transport module.
[    9.818427] RPC: Registered udp transport module.
[    9.818432] RPC: Registered tcp transport module.
[    9.818437] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   10.485496] ehci-omap 4a064c00.ehci: port 2 reset error -110
[   10.490908] systemd-journald[1854]: Received request to flush runtime journal from PID 1
[   11.375516] ehci-omap 4a064c00.ehci: port 2 reset error -110
[   11.553802] Bluetooth: Core ver 2.22
[   11.585940] NET: Registered protocol family 31
[   11.612368] Bluetooth: HCI device and connection manager initialized
[   11.638766] Bluetooth: HCI socket layer initialized
[   11.648287] bmg160_i2c 2-0069: mounting matrix not found: using identity...
[   11.660006] Bluetooth: L2CAP socket layer initialized
[   11.735293] bmg160_i2c 2-0069: Error reading reg_chip_id
[   11.748171] Bluetooth: SCO socket layer initialized
[   11.760134] bmg160_i2c: probe of 2-0069 failed with error -121
[   11.798562] input: twl6040:vibrator as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48070000.target-module/48070000.i2c/i2c-0/0-004b/twl6040-vibra/input/input9
[   11.835451] ina2xx 1-004f: power monitor ina231 (Rshunt = 20000 uOhm)
[   11.936611] gpio gpiochip10: (4-0022): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[   11.976978] Bluetooth: HCI UART driver ver 2.3
[   12.064070] usb usb1-port2: Cannot enable. Maybe the USB cable is bad?
[   12.138009] input input2: as5013_open
[   12.175539] ehci-omap 4a064c00.ehci: port 2 reset error -110
[   12.242922] input input3: as5013_open
[   12.253146] Bluetooth: HCI UART protocol H4 registered
[   12.270937] Bluetooth: HCI UART protocol BCSP registered
[   12.283694] Bluetooth: HCI UART protocol LL registered
[   12.295168] Bluetooth: HCI UART protocol Broadcom registered
[   12.323061] input input2: as5013_open
[   12.337862] input input3: as5013_open
[   12.364323] Bluetooth: hci0: change remote baud rate command in firmware
[   12.408322] gpio gpiochip10: (4-0022): unable to lock HW IRQ 14 for IRQ
[   12.421999] genirq: Failed to request resources for TS3A227E (irq 197) on irqchip 4-0022
[   12.436770] ts3a227e 4-003b: Cannot request irq 197 (-5)
[   12.456088] ts3a227e: probe of 4-003b failed with error -5
[   12.809976] EXT4-fs (mmcblk0p1): warning: mounting unchecked fs, running e2fsck is recommended
[   12.844546] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null)
[   12.867556] ext4 filesystem being mounted at /boot supports timestamps until 2038 (0x7fffffff)
[   13.155510] ehci-omap 4a064c00.ehci: port 2 reset error -110
[   13.250581] emif_probe: error getting device data
[   13.250613] emif_probe: error getting device data
[   13.317575] emif_probe: error getting device data
[   13.317629] emif_probe: error getting device data
[   13.933623] PVR_K: UM DDK-(3699939) and KM DDK-(3699939) match. [ OK ]
[   14.035735] ehci-omap 4a064c00.ehci: port 2 reset error -110
[   14.625597] asoc-simple-card sound_bluetooth: W2CBW003 <-> 40122000.mcbsp mapping ok
[   14.708568] asoc-simple-card sound_fmradio: W2CBW003 <-> 40124000.mcbsp mapping ok
[   14.915652] ehci-omap 4a064c00.ehci: port 2 reset error -110
[   15.245937] wwan_on_off_rfkill_set_block: blocked: 0
[   15.274660] wwan_on_off_set_power:on = 1
[   15.282931] wwan_on_off_is_powered_on: gpio value = 0
[   15.306931] snd_soc_omap_abe_twl6040: unknown parameter 'index' ignored
[   15.314032] wwan_on_off_is_powered_on: return 'false'
[   15.338564] wwan_on_off_set_power: state 0
[   15.351841] asoc-simple-card sound_telephony: gtm601 <-> 40126000.mcbsp mapping ok
[   15.358444] wwan_on_off_set_power: regulator 0
[   15.516269] omap-abe-twl6040 sound: ASoC: unknown pin AFML
[   15.561099] omap-abe-twl6040 sound: ASoC: unknown pin AFMR
[   15.585201] omap-abe-twl6040 sound: twl6040-legacy <-> 40132000.mcpdm mapping ok
[   15.764101] input: Letux Cortex 15 Headset Jack as /devices/platform/sound/sound/card4/input10
[   15.815520] ehci-omap 4a064c00.ehci: port 2 reset error -110
[   16.065472] wl18xx_driver wl18xx.2.auto: Direct firmware load for ti-connectivity/wl18xx-conf.bin failed with error -2
[   16.065485] wl18xx_driver wl18xx.2.auto: Falling back to sysfs fallback for: ti-connectivity/wl18xx-conf.bin
[   16.073489] wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin: -11
[   16.073489] wlcore: WARNING falling back to default config
[   16.474154] usb usb1-port2: Cannot enable. Maybe the USB cable is bad?
[   16.489352] usb usb1-port2: attempt power cycle
[   16.596308] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)
[   16.616762] wlcore: WARNING Detected unconfigured mac address in nvs, derive from fuse instead.
[   16.634705] wlcore: WARNING This default nvs file can be removed from the file system
[   17.582425] wwan_on_off_set_power: send impulse
[   18.334292] wwan_on_off_is_powered_on: gpio value = 1
[   18.365728] wwan_on_off_is_powered_on: return 'true'
[   18.397372] wwan_on_off_set_power: done
[   18.425875] wlcore: loaded
[   18.489199] input input2: as5013_open
[   18.489291] input input3: as5013_open
[   18.510705] input: pyraInput keyboard as /devices/virtual/input/input11
[   18.511034] input: pyraInput Gamepad as /devices/virtual/input/input12
[   18.511575] input: pyraInput Mouse as /devices/virtual/input/input13
[   18.978732] wwan_on_off_rfkill_set_block: blocked: 0
[   18.978742] wwan_on_off_set_power:on = 1
[   18.978752] wwan_on_off_is_powered_on: gpio value = 1
[   18.978758] wwan_on_off_is_powered_on: return 'true'
[   18.978762] wwan_on_off_set_power: state 1
[   18.978762] wwan_on_off_set_power: regulator 1
[   18.978762] wwan_on_off_set_power: done
[   19.162205] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   19.180694] Bluetooth: BNEP socket layer initialized
[   19.990389] wlcore: PHY firmware version: Rev 8.2.0.0.242
[   20.094363] wlcore: firmware booted (Rev 8.9.0.0.79)
[   20.122452] wlcore: down
[   20.604922] wlcore: PHY firmware version: Rev 8.2.0.0.242
[   20.713478] wlcore: firmware booted (Rev 8.9.0.0.79)
[   23.513515] fuse: init (API version 7.31)
[   25.192516] wlcore: down
[   29.286715] wlan0: authenticate with e0:22:04:22:8d:9a
[   29.306723] wlan0: send auth to e0:22:04:22:8d:9a (try 1/3)
[   29.343813] wlan0: authenticated
[   29.354189] wlan0: associate with e0:22:04:22:8d:9a (try 1/3)
[   29.364657] wlan0: RX AssocResp from e0:22:04:22:8d:9a (capab=0x511 status=0 aid=44)
[   29.393191] wlan0: associated
[   29.434817] wlan0: Limiting TX power to 127 (127 - 0) dBm as advertised by e0:22:04:22:8d:9a
[   29.649874] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   29.663668] wlcore: Association completed.
[   31.274048] Bluetooth: RFCOMM socket layer initialized
[   31.279482] Bluetooth: RFCOMM ver 1.11
[   36.324068] host1_vbus_power: supplied by modem_vbus_hdmi_power
[   36.330691] host2_vbus_power: supplied by modem_vbus_hdmi_power
[   36.343142] ldo3: disabling
[   36.348544] ldo8: disabling
[   36.352804] otg_path: disabling
[   99.664950] [UFW BLOCK] IN=wlan0 OUT= MAC=01:00:5e:00:00:01:e0:22:04:22:8d:91:08:00 SRC=192.168.1.254 DST=224.0.0.1 LEN=36 TOS=0x00 PREC=0xC0 TTL=1 ID=0 DF PROTO=2

 

[EvilDragon]

Thanks A quick dmesg with the error message when you connect a USB device in that non-working state would be helpful as well

 

[Kazuki]

Nothing seemed to change in the dmesg. ran dmesg before and after inserting usb device and got the samething.

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 5.6.19-daveiii-pyradef-aufs (pyra@debian-buster) (gcc version 8.3.0 (Debian 8.3.0-2)) #3 SMP PREEMPT Mon Dec 14 18:23:52 CET 2020
[    0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[    0.000000] OF: fdt: Machine model: Pyra-Handheld-V5.3
[    0.000000] printk: debug: ignoring loglevel setting.
[    0.000000] printk: debug: ignoring loglevel setting.
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 64 MiB at 0x00000000fb000000
[    0.000000] OMAP4: Map 0x00000000afd00000 to (ptrval) for dram barrier
[    0.000000] On node 0 totalpages: 1043712
[    0.000000]   DMA zone: 2295 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 195840 pages, LIFO batch:63
[    0.000000]   HighMem zone: 847872 pages, LIFO batch:63
[    0.000000] OMAP5432 ES2.0
[    0.000000] percpu: Embedded 20 pages/cpu s50316 r8192 d23412 u81920
[    0.000000] pcpu-alloc: s50316 r8192 d23412 u81920 alloc=20*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1041417
[    0.000000] Kernel command line: root=PARTUUID=094c7470-02 console=ttyO2,115200n8 console=tty0 vram=12M omapfb.vram=0:8M,1:4M omapfb.rotate_type=0 omapdss.def_disp=lcd rootwait twl4030_charger.allow_usb=1 musb_hdrc.preserve_vbus=1 log_buf_len=8M ignore_loglevel earlyprintk drm_kms_helper.fbdev_rotation=8 drm.force_hw_rotation fastboot coherent_pool=1M twl4030_charger.allow_usb=1 fsck.repair=yes rootfstype=f2fs  rootwait ignore_loglevel
[    0.000000] printk: log_buf_len: 8388608 bytes
[    0.000000] printk: early log buf free: 63724(97%)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: mapped [mem 0xa53bf000-0xa93bf000] (64MB)
[    0.000000] Memory: 3948708K/4174848K available (10478K kernel code, 908K rwdata, 2772K rodata, 2048K init, 269K bss, 160604K reserved, 65536K cma-reserved, 3325952K highmem)
[    0.000000] random: get_random_u32 called from __kmem_cache_create+0x34/0x4f8 with crng_init=0
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[    0.000000]     Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] OMAP clockevent source: timer1 at 32768 Hz
[    0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16ac02862, max_idle_ns: 440795202218 ns
[    0.000010] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511085ns
[    0.000033] Switching to timer-based delay loop, resolution 162ns
[    0.000164] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[    0.000179] OMAP clocksource: 32k_counter at 32768 Hz
[    0.002034] Console: colour dummy device 80x30
[    0.002995] printk: console [tty0] enabled
[    0.003066] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.28 BogoMIPS (lpj=61440)
[    0.003116] pid_max: default: 32768 minimum: 301
[    0.003404] LSM: Security Framework initializing
[    0.003538] Yama: becoming mindful.
[    0.003712] AppArmor: AppArmor initialized
[    0.003751] TOMOYO Linux initialized
[    0.003870] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.003916] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.005193] CPU: Testing write buffer coherency: ok
[    0.005276] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.005732] /cpus/cpu@0 missing clock-frequency property
[    0.005791] /cpus/cpu@1 missing clock-frequency property
[    0.005826] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.059699] Setting up static identity map for 0x80200000 - 0x80200060
[    0.079701] rcu: Hierarchical SRCU implementation.
[    0.119736] smp: Bringing up secondary CPUs ...
[    0.200079] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.200092] CPU1: Spectre v2: using ICIALLU workaround
[    0.200224] smp: Brought up 1 node, 2 CPUs
[    0.200239] SMP: Total of 2 processors activated (24.57 BogoMIPS).
[    0.200254] CPU: All CPU(s) started in HYP mode.
[    0.200264] CPU: Virtualization extensions available.
[    0.200701] devtmpfs: initialized
[    0.215025] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.215468] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.215499] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.216825] pinctrl core: initialized pinctrl subsystem
[    0.217647] thermal_sys: Registered thermal governor 'fair_share'
[    0.217649] thermal_sys: Registered thermal governor 'step_wise'
[    0.217659] thermal_sys: Registered thermal governor 'user_space'
[    0.218534] NET: Registered protocol family 16
[    0.221071] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.222065] omap_hwmod: l3_main_3 using broken dt data from ocp
[    0.222879] omap_hwmod: l3_main_2 using broken dt data from ocp
[    0.235960] audit: initializing netlink subsys (disabled)
[    0.236173] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1
[    0.239927] cpuidle: using governor menu
[    0.266233] platform 50000000.gpmc: Cannot lookup hwmod 'gpmc'
[    0.266416] omap-gpmc 50000000.gpmc: _od_fail_runtime_resume: FIXME: missing hwmod/omap_dev info
[    0.266447] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[    0.275114] No ATAGs?
[    0.275175] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.275205] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.296975] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.303070] vsys_cobra: supplied by vmain
[    0.307340] iommu: Default domain type: Translated 
[    0.309507] vgaarb: loaded
[    0.310178] SCSI subsystem initialized
[    0.311369] libata version 3.00 loaded.
[    0.311857] usbcore: registered new interface driver usbfs
[    0.311964] usbcore: registered new interface driver hub
[    0.312101] usbcore: registered new device driver usb
[    0.312376] usb_phy_generic hsusb2_phy: hsusb2_phy supply vcc not found, using dummy regulator
[    0.314176] Advanced Linux Sound Architecture Driver Initialized.
[    0.314848] NetLabel: Initializing
[    0.314860] NetLabel:  domain hash size = 128
[    0.314878] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.314939] NetLabel:  unlabeled traffic allowed by default
[    0.315733] clocksource: Switched to clocksource arch_sys_counter
[    0.382230] VFS: Disk quotas dquot_6.6.0
[    0.382291] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.382932] AppArmor: AppArmor Filesystem Enabled
[    0.394743] NET: Registered protocol family 2
[    0.395247] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[    0.395292] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.395359] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.395506] TCP: Hash tables configured (established 8192 bind 8192)
[    0.395597] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.395642] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.395892] NET: Registered protocol family 1
[    0.396726] PCI: CLS 0 bytes, default 64
[    0.397184] Trying to unpack rootfs image as initramfs...
[    1.249409] Freeing initrd memory: 18612K
[    1.249937] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[    1.250150] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    1.252496] Initialise system trusted keyrings
[    1.252622] workingset: timestamp_bits=14 max_order=20 bucket_order=6
[    1.262883] zbud: loaded
[    1.267800] jitterentropy: Initialization failed with host not compliant with requirements: 2
[    1.267823] Key type asymmetric registered
[    1.267851] Asymmetric key parser 'x509' registered
[    1.267888] bounce: pool size: 64 pages
[    1.267997] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[    1.268011] io scheduler mq-deadline registered
[    1.268034] io scheduler kyber registered
[    1.273710] OMAP GPIO hardware version 0.1
[    1.298617] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
[    1.371502] GPIO line 74 (gpio8_234/msecure) hogged as output/high
[    1.399473] ti-pipe3 4a096000.phy: can't get syscon-pllreset, sata dpll won't idle
[    1.401029] pinctrl-single 4ae0c840.pinmux: 30 pins, size 60
[    1.401695] pinctrl-single 4a002840.pinmux: 219 pins, size 438
[    1.405881] pwm-backlight keyboard-backlight: keyboard-backlight supply power not found, using dummy regulator
[    1.406177] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    1.411123] ti_abb 4ae07cdc.regulator-abb-mpu: can't request region for resource [mem 0x4ae07cdc-0x4ae07ce3]
[    1.411160] ti_abb: probe of 4ae07cdc.regulator-abb-mpu failed with error -16
[    1.411222] ti_abb 4ae07ce4.regulator-abb-mm: can't request region for resource [mem 0x4ae07ce4-0x4ae07ceb]
[    1.411248] ti_abb: probe of 4ae07ce4.regulator-abb-mm failed with error -16
[    1.411710] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.414426] 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 108, base_baud = 3000000) is a OMAP UART2
[    2.373855] printk: console [ttyO2] enabled
[    2.378965] omap_uart 48068000.serial: no wakeirq for uart5
[    2.385009] 48068000.serial: ttyO5 at MMIO 0x48068000 (irq = 121, base_baud = 3000000) is a OMAP UART5
[    2.395533] omap_uart 4806c000.serial: no wakeirq for uart1
[    2.401607] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 122, base_baud = 3000000) is a OMAP UART1
[    2.411680] serial serial0: tty port ttyO1 registered
[    2.417214] omap_uart 4806e000.serial: no wakeirq for uart3
[    2.423275] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 123, base_baud = 3000000) is a OMAP UART3
[    2.435033] omap_rng 48090000.rng: Random Number Generator ver. 20
[    2.435587] random: fast init done
[    2.442350] omapdss_dss 58000000.dss: 58000000.dss supply vdda_video not found, using dummy regulator
[    2.445298] random: crng init done
[    2.458799] DSS: OMAP DSS rev 6.1
[    2.476340] brd: module loaded
[    2.484462] loop: module loaded
[    2.487829] wwan_on_off_init: wwan_on_off_init
[    2.492936] wwan_on_off_probe: wwan_on_off_probe()
[    2.500333] ahci 4a140000.sata: 4a140000.sata supply ahci not found, using dummy regulator
[    2.509226] ahci 4a140000.sata: 4a140000.sata supply phy not found, using dummy regulator
[    2.517980] ahci 4a140000.sata: 4a140000.sata supply target not found, using dummy regulator
[    2.527097] ahci 4a140000.sata: SSS flag set, parallel bus scan disabled
[    2.534177] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    2.543222] ahci 4a140000.sata: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part ccc apst 
[    2.554120] scsi host0: ahci
[    2.557665] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 31
[    2.566667] mtdoops: mtd device (mtddev=name/number) must be supplied
[    2.575224] libphy: Fixed MDIO Bus: probed
[    2.583128] omap-dwc3 4a020000.omap_dwc3: vbus init failed
[    2.589235] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.596189] ehci-pci: EHCI PCI platform driver
[    2.600970] usbcore: registered new interface driver usb-storage
[    2.607918] mousedev: PS/2 mouse device common for all mice
[    2.615385] i2c /dev entries driver
[    2.619199] IR NEC protocol handler initialized
[    2.623979] IR RC5(x/sz) protocol handler initialized
[    2.629355] IR RC6 protocol handler initialized
[    2.634139] IR JVC protocol handler initialized
[    2.638944] IR Sony protocol handler initialized
[    2.643814] IR SANYO protocol handler initialized
[    2.648820] IR Sharp protocol handler initialized
[    2.653793] IR MCE Keyboard/mouse protocol handler initialized
[    2.659971] IR XMP protocol handler initialized
[    2.664748] Driver for 1-wire Dallas network protocol.
[    2.674497] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[    2.684080] sdhci: Secure Digital Host Controller Interface driver
[    2.690640] sdhci: Copyright(c) Pierre Ossman
[    2.696195] omap_gpio 48053000.gpio: Could not set line 4 debounce to 200000 microseconds (-22)
[    2.705374] omap_hsmmc 4809c000.mmc: Got CD GPIO
[    2.710301] omap_hsmmc 4809c000.mmc: Got WP GPIO
[    2.752134] omap_gpio 48057000.gpio: Could not set line 13 debounce to 200000 microseconds (-22)
[    2.761541] omap_hsmmc 480d1000.mmc: Got CD GPIO
[    2.766538] omap_hsmmc 480d1000.mmc: Got WP GPIO
[    2.776182] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.782865] txs02612 txs02612: probe
[    2.786776] txs02612 txs02612: failed to get mmc phandle in /txs02612 node
[    2.794053] txs02612 txs02612: could not get access to host port, using manual mode
[    2.825773] txs02612_request: current=1 client=0
[    2.855772] txs02612 txs02612: probed
[    2.859767] txs02612_request: current=0 client=1
[    2.864659] ledtrig-cpu: registered to indicate activity on CPUs
[    2.873405] usbcore: registered new interface driver usbhid
[    2.879362] usbhid: USB HID core driver
[    2.883634] ashmem: initialized
[    2.892569] oprofile: using timer interrupt.
[    2.897184] ata1: SATA link down (SStatus 0 SControl 300)
[    2.902965] drop_monitor: Initializing network drop monitor service
[    2.910337] NET: Registered protocol family 10
[    2.942676] Segment Routing with IPv6
[    2.946653] mip6: Mobile IPv6
[    2.949791] NET: Registered protocol family 17
[    2.954496] mpls_gso: MPLS GSO support
[    2.958857] ThumbEE CPU extension supported.
[    2.963374] Registering SWP/SWPB emulation handler
[    2.968500] omap_vc_init_channel: No PMIC info for vdd_core
[    2.974381] omap_vp_init: No PMIC info for vdd_core
[    2.979585] omap_vc_init_channel: No PMIC info for vdd_mm
[    2.985299] omap_vp_init: No PMIC info for vdd_mm
[    2.990324] omap_vc_init_channel: No PMIC info for vdd_mpu
[    2.996122] omap_vp_init: No PMIC info for vdd_mpu
[    3.001174] Power Management for TI OMAP4+ devices.
[    3.007017] Loading compiled-in X.509 certificates
[    3.016038] Loaded X.509 cert 'Build time autogenerated kernel key: 4020818a539cdd7ae890874388bde6caf4fc6257'
[    3.027126] Key type ._fscrypt registered
[    3.031358] Key type .fscrypt registered
[    3.035509] Key type fscrypt-provisioning registered
[    3.041166] AppArmor: AppArmor sha1 policy hashing enabled
[    3.068052] dmm 4e000000.dmm: initialized all PAT entries
[    3.077655] omap-iommu 4a066000.mmu: 4a066000.mmu registered
[    3.085266] bmc150_accel_i2c 2-0010: mounting matrix not found: using identity...
[    3.119162] bmc150_accel_i2c 2-0010: Error: Reading chip id
[    3.125120] bmc150_accel_i2c: probe of 2-0010 failed with error -121
[    3.132354] bmc150_magn_i2c 2-0012: mounting matrix not found: using identity...
[    3.140379] bmc150_magn_i2c 2-0012: Failed to bring up device from suspend mode
[    3.148269] bmc150_magn_i2c: probe of 2-0012 failed with error -121
[    3.155228] bmp280 2-0077: 2-0077 supply vddd not found, using dummy regulator
[    3.163057] bmp280 2-0077: 2-0077 supply vdda not found, using dummy regulator
[    3.181733] bmp280: probe of 2-0077 failed with error -121
[    3.187986] bmp280 2-0076: 2-0076 supply vddd not found, using dummy regulator
[    3.195681] bmp280 2-0076: 2-0076 supply vdda not found, using dummy regulator
[    3.215421] bno055 2-0029: mounting matrix not found: using identity...
[    3.229464] bno055 2-0029: software revision id 0311
[    3.237121] input: iio-bridge: bno055 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48060000.target-module/48060000.i2c/i2c-2/2-0029/iio:device1/input/input0
[    3.256712] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz
[    3.263670] palmas 0-0048: Irq flag is 0x00000008
[    3.309036] palmas 0-0048: Muxing GPIO 3, PWM 0, LED 0
[    3.323001] palmas-rtc 48070000.i2c:palmas@48:rtc: registered as rtc0
[    3.333085] SMPS123: supplied by regulator-dummy
[    3.339686] SMPS45: supplied by regulator-dummy
[    3.346128] SMPS6: supplied by vsys_cobra
[    3.351754] SMPS7: supplied by vsys_cobra
[    3.357542] SMPS8: supplied by vsys_cobra
[    3.363250] SMPS9: supplied by vsys_cobra
[    3.367765] smps9: Bringing 0uV into 2100000-2100000uV
[    3.374540] SMPS10_OUT2: supplied by regulator-dummy
[    3.381010] SMPS10_OUT1: supplied by regulator-dummy
[    3.387062] LDO1: supplied by vsys_cobra
[    3.391401] ldo1: Bringing 0uV into 1800000-1800000uV
[    3.398161] LDO2: supplied by vsys_cobra
[    3.402479] ldo2: Bringing 0uV into 1800000-1800000uV
[    3.411100] ldo4: Bringing 0uV into 1800000-1800000uV
[    3.417905] LDO5: supplied by vsys_cobra
[    3.427181] LDO7: supplied by vsys_cobra
[    3.431608] ldo7: Bringing 0uV into 2000000-2000000uV
[    3.438417] LDO8: supplied by vsys_cobra
[    3.444166] LDO9: supplied by vmmcsd_fixed
[    3.450687] LDOLN: supplied by vsys_cobra
[    3.456693] LDOUSB: supplied by vsys_cobra
[    3.464902] palmas_pwrbutton 48070000.i2c:palmas@48:palmas_power_button: h/w controlled shutdown duration=8 seconds
[    3.477068] input: palmas_pwron as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48070000.target-module/48070000.i2c/i2c-0/0-0048/48070000.i2c:palmas@48:palmas_power_button/input/input1
[    3.502146] usb3503 0-0008: usb3503_probe
[    3.515772] usb3503 0-0008: reset gpio state 1
[    3.520475] usb3503 0-0008: usb3503_connect
[    3.524921] usb3503 0-0008: usb3503_reset 1
[    3.535814] usb3503 0-0008: SP_ILOCK failed (-121)
[    3.540891] usb3503 0-0008: usb3503_probe: probed in hub mode
[    3.547361] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
[    3.586477] as5013 1-0040: ID code: 0c
[    3.590788] as5013 1-0040: ID version: 0d
[    3.595365] as5013 1-0040: silicon revision: 00
[    3.600492] as5013 1-0040: control: f1
[    3.604582] input: nub0 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48072000.target-module/48072000.i2c/i2c-1/1-0040/input/input2
[    3.621458] as5013 1-0040: probe 40, gpio -2, irq 0, "as5013"
[    3.628330] as5013 1-0041: ID code: 0c
[    3.632658] as5013 1-0041: ID version: 0d
[    3.637267] as5013 1-0041: silicon revision: 00
[    3.642188] as5013 1-0041: control: f1
[    3.646414] input: nub1 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48072000.target-module/48072000.i2c/i2c-1/1-0041/input/input3
[    3.663293] as5013 1-0041: probe 41, gpio -2, irq 0, "as5013"
[    3.671201] input: tca8418 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48072000.target-module/48072000.i2c/i2c-1/1-0034/input/input4
[    3.688352] bq27xxx_battery_setup
[    3.691853] bq27xxx_battery_setup: dm_regs=8f9cf4ce
[    3.697477] bq27xxx_battery_settings
[    3.701261] bq27xxx_battery_set_config
[    3.705208] bq27xxx_battery_unseal
[    3.717791] bq27xxx_battery_update_dm_block
[    3.722221] bq27xxx-battery 1-0055: design-capacity has 6000
[    3.728239] bq27xxx_battery_update_dm_block
[    3.732680] bq27xxx-battery 1-0055: design-energy has 22200
[    3.738615] bq27xxx_battery_update_dm_block
[    3.743062] bq27xxx-battery 1-0055: terminate-voltage has 3200
[    3.749257] bq27xxx_battery_seal
[    3.758268] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
[    3.806740] input: TSC2007 Touchscreen as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/4807a000.target-module/4807a000.i2c/i2c-3/3-0048/input/input5
[    3.826627] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
[    3.834623] vdds_1v8_main: supplied by smps7
[    3.839719] pca953x 4-0022: using AI
[    3.879636] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz
[    3.887998] omap-iommu 55082000.mmu: 55082000.mmu registered
[    3.895506] pwm-backlight keyboard-backlight: keyboard-backlight supply power not found, using dummy regulator
[    3.906580] dmtimer posted=0
[    3.909971] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[    3.919645] ldo4: supplied by vdds_1v8_main
[    3.930845] wwan_on_off_probe: wwan_on_off_probe()
[    3.936554] omap-dwc3 4a020000.omap_dwc3: vbus init failed
[    3.945699] omap_gpio 48053000.gpio: Could not set line 4 debounce to 200000 microseconds (-22)
[    3.954918] omap_hsmmc 4809c000.mmc: Got CD GPIO
[    3.959866] omap_hsmmc 4809c000.mmc: Got WP GPIO
[    3.996349] omap_hsmmc 480ad000.mmc: allocated mmc-pwrseq
[    4.070147] mmc3: new high speed SDXC card at address aaaa
[    4.079050] mmcblk3: mmc3:aaaa SF256 238 GiB 
[    4.085447]  mmcblk3: p1
[    4.114285] omap_gpio 48057000.gpio: Could not set line 13 debounce to 200000 microseconds (-22)
[    4.123630] omap_hsmmc 480d1000.mmc: Got CD GPIO
[    4.128599] omap_hsmmc 480d1000.mmc: Got WP GPIO
[    4.139707] omap_hsmmc 480ad000.mmc: card claims to support voltages below defined range
[    4.164520] mmc4: new high speed SDIO card at address 0001
[    4.256509] ldo3: supplied by vdds_1v8_main
[    4.261106] ldo6: supplied by vdds_1v8_main
[    4.450041] mmc5: new high speed SDXC card at address aaaa
[    4.459043] mmcblk5: mmc5:aaaa SF256 238 GiB 
[    4.466367] bq2429x_charger 1-006b: bq2429x_parse_dt,line=1539 chg_current = 2048000 usb_input_current = 3000000 adp_input_current = 2048000 bat_volt_max = 4200000
[    4.482693] bq2429x_charger 1-006b: found regulator-max-microvolt = 4200000
[    4.490344]  mmcblk5: p1
[    4.505797] vsys: Bringing 3300000uV into 3500000-3500000uV
[    4.516233] omapdss_dss 58000000.dss: bound 58001000.dispc (ops 0xc0ca350c)
[    4.523649] omapdss_dss 58000000.dss: bound 58004000.encoder (ops 0xc0ca52d4)
[    4.531980] omap-hdmi-audio omap-hdmi-audio.1.auto: snd-soc-dummy-dai <-> 58040000.encoder mapping ok
[    4.543137] omapdss_dss 58000000.dss: bound 58040000.encoder (ops 0xc0ca6160)
[    4.552642] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    4.559629] [drm] No driver support for vblank timestamp query.
[    4.597955] drm_setup_crtcs_fb: sw_rotations=1
[    4.602650] drm_setup_crtcs_fb: fbcon_rotate_hint=0
[    4.613646] ------------[ cut here ]------------
[    4.613671] WARNING: CPU: 0 PID: 59 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x254/0x374
[    4.613676] 44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4WAKEUP (Idle): Data Access in User mode during Functional access
[    4.613676] Modules linked in:
[    4.613676] CPU: 0 PID: 59 Comm: kworker/0:1 Not tainted 5.6.19-daveiii-pyradef-aufs #3
[    4.613676] Hardware name: Generic OMAP5 (Flattened Device Tree)
[    4.613689] Workqueue: events deferred_probe_work_func
[    4.613706] [<c0212e60>] (unwind_backtrace) from [<c020d1a0>] (show_stack+0x10/0x14)
[    4.613706] [<c020d1a0>] (show_stack) from [<c0c1b544>] (dump_stack+0x94/0xa8)
[    4.613722] [<c0c1b544>] (dump_stack) from [<c02351f0>] (__warn+0xd0/0xf8)
[    4.613737] [<c02351f0>] (__warn) from [<c02355e0>] (warn_slowpath_fmt+0x94/0xb8)
[    4.613737] [<c02355e0>] (warn_slowpath_fmt) from [<c064c23c>] (l3_interrupt_handler+0x254/0x374)
[    4.613739] [<c064c23c>] (l3_interrupt_handler) from [<c0290864>] (__handle_irq_event_percpu+0x58/0x29c)
[    4.613751] [<c0290864>] (__handle_irq_event_percpu) from [<c0290ad4>] (handle_irq_event_percpu+0x2c/0x80)
[    4.613762] [<c0290ad4>] (handle_irq_event_percpu) from [<c0290b60>] (handle_irq_event+0x38/0x5c)
[    4.613767] [<c0290b60>] (handle_irq_event) from [<c02950f4>] (handle_fasteoi_irq+0xb8/0x168)
[    4.613767] [<c02950f4>] (handle_fasteoi_irq) from [<c028fae4>] (generic_handle_irq+0x24/0x34)
[    4.613767] [<c028fae4>] (generic_handle_irq) from [<c02900b8>] (__handle_domain_irq+0x5c/0xb4)
[    4.613778] [<c02900b8>] (__handle_domain_irq) from [<c064a570>] (gic_handle_irq+0x3c/0x78)
[    4.613791] [<c064a570>] (gic_handle_irq) from [<c0201ab8>] (__irq_svc+0x58/0x8c)
[    4.613797] Exception stack(0xedad5830 to 0xedad5878)
[    4.613798] 5820:                                     edd75290 000c0013 fce10194 00000003
[    4.613798] 5840: cf1b2840 00000001 c1203fc8 cf1a3810 cf1b28c4 00000000 c0ca7668 00000000
[    4.613798] 5860: 00000194 edad5880 c077f224 c0c39984 200c0013 ffffffff
[    4.613804] [<c0201ab8>] (__irq_svc) from [<c0c39984>] (_raw_spin_unlock_irqrestore+0x1c/0x4c)
[    4.613818] [<c0c39984>] (_raw_spin_unlock_irqrestore) from [<c077f224>] (w677l_regulator+0x58/0x64)
[    4.613828] [<c077f224>] (w677l_regulator) from [<c077f5a8>] (w677l_enable+0xf8/0x3dc)
[    4.613828] [<c077f5a8>] (w677l_enable) from [<c0764768>] (omapdss_device_enable+0x20/0x34)
[    4.613833] [<c0764768>] (omapdss_device_enable) from [<c07829a4>] (omap_encoder_enable+0x40/0x80)
[    4.613849] [<c07829a4>] (omap_encoder_enable) from [<c072abc4>] (drm_atomic_helper_commit_modeset_enables+0x23c/0x268)
[    4.613859] [<c072abc4>] (drm_atomic_helper_commit_modeset_enables) from [<c078007c>] (omap_atomic_commit_tail+0x48/0xc0)
[    4.613859] [<c078007c>] (omap_atomic_commit_tail) from [<c072bcdc>] (commit_tail+0x9c/0x1b0)
[    4.613859] [<c072bcdc>] (commit_tail) from [<c072c8e0>] (drm_atomic_helper_commit+0x134/0x158)
[    4.613873] [<c072c8e0>] (drm_atomic_helper_commit) from [<c0759534>] (drm_client_modeset_commit_atomic+0x16c/0x210)
[    4.613885] [<c0759534>] (drm_client_modeset_commit_atomic) from [<c0759630>] (drm_client_modeset_commit_force+0x58/0x184)
[    4.613889] [<c0759630>] (drm_client_modeset_commit_force) from [<c0731024>] (drm_fb_helper_restore_fbdev_mode_unlocked+0x54/0x98)
[    4.613889] [<c0731024>] (drm_fb_helper_restore_fbdev_mode_unlocked) from [<c0731098>] (drm_fb_helper_set_par+0x30/0x5c)
[    4.613891] [<c0731098>] (drm_fb_helper_set_par) from [<c06a4c4c>] (fbcon_init+0x3e0/0x578)
[    4.613906] [<c06a4c4c>] (fbcon_init) from [<c06f1c0c>] (visual_init+0xbc/0x104)
[    4.613920] [<c06f1c0c>] (visual_init) from [<c06f30ec>] (do_bind_con_driver+0x1e0/0x3bc)
[    4.613920] [<c06f30ec>] (do_bind_con_driver) from [<c06f3618>] (do_take_over_console+0x138/0x1d4)
[    4.613920] [<c06f3618>] (do_take_over_console) from [<c06a1334>] (do_fbcon_takeover+0x74/0xd4)
[    4.613935] [<c06a1334>] (do_fbcon_takeover) from [<c0698fa4>] (register_framebuffer+0x204/0x2dc)
[    4.613948] [<c0698fa4>] (register_framebuffer) from [<c0730b2c>] (__drm_fb_helper_initial_config_and_unlock+0x404/0x5ac)
[    4.613950] [<c0730b2c>] (__drm_fb_helper_initial_config_and_unlock) from [<c0788c00>] (omap_fbdev_init+0x8c/0xc4)
[    4.613950] [<c0788c00>] (omap_fbdev_init) from [<c07805e0>] (pdev_probe+0x4ec/0x788)
[    4.613954] [<c07805e0>] (pdev_probe) from [<c0795a74>] (platform_drv_probe+0x48/0x98)
[    4.613965] [<c0795a74>] (platform_drv_probe) from [<c079357c>] (really_probe+0x1c8/0x458)
[    4.613976] [<c079357c>] (really_probe) from [<c0793ac0>] (driver_probe_device+0x158/0x1b0)
[    4.613981] [<c0793ac0>] (driver_probe_device) from [<c07917c8>] (bus_for_each_drv+0x80/0xc4)
[    4.613981] [<c07917c8>] (bus_for_each_drv) from [<c0793320>] (__device_attach+0xd0/0x15c)
[    4.613981] [<c0793320>] (__device_attach) from [<c0792534>] (bus_probe_device+0x84/0x8c)
[    4.613992] [<c0792534>] (bus_probe_device) from [<c078ef0c>] (device_add+0x65c/0x798)
[    4.614004] [<c078ef0c>] (device_add) from [<c0795844>] (platform_device_add+0x130/0x23c)
[    4.614011] [<c0795844>] (platform_device_add) from [<c07963b4>] (platform_device_register_full+0xd0/0x110)
[    4.614011] [<c07963b4>] (platform_device_register_full) from [<c0765900>] (dss_bind+0x80/0xa8)
[    4.614011] [<c0765900>] (dss_bind) from [<c078c67c>] (try_to_bring_up_master+0x1ec/0x2a8)
[    4.614019] [<c078c67c>] (try_to_bring_up_master) from [<c078c7d4>] (__component_add+0x9c/0x168)
[    4.614030] [<c078c7d4>] (__component_add) from [<c077d0b0>] (hdmi5_probe+0x1ec/0x244)
[    4.614041] [<c077d0b0>] (hdmi5_probe) from [<c0795a74>] (platform_drv_probe+0x48/0x98)
[    4.614042] [<c0795a74>] (platform_drv_probe) from [<c079357c>] (really_probe+0x1c8/0x458)
[    4.614042] [<c079357c>] (really_probe) from [<c0793ac0>] (driver_probe_device+0x158/0x1b0)
[    4.614042] [<c0793ac0>] (driver_probe_device) from [<c07917c8>] (bus_for_each_drv+0x80/0xc4)
[    4.614053] [<c07917c8>] (bus_for_each_drv) from [<c0793320>] (__device_attach+0xd0/0x15c)
[    4.614062] [<c0793320>] (__device_attach) from [<c0792534>] (bus_probe_device+0x84/0x8c)
[    4.614072] [<c0792534>] (bus_probe_device) from [<c0792a60>] (deferred_probe_work_func+0x78/0xb8)
[    4.614072] [<c0792a60>] (deferred_probe_work_func) from [<c02510dc>] (process_one_work+0x22c/0x5c8)
[    4.614072] [<c02510dc>] (process_one_work) from [<c025170c>] (worker_thread+0x294/0x598)
[    4.614077] [<c025170c>] (worker_thread) from [<c0257a00>] (kthread+0x150/0x154)
[    4.614091] [<c0257a00>] (kthread) from [<c02010d8>] (ret_from_fork+0x14/0x3c)
[    4.614096] Exception stack(0xedad5fb0 to 0xedad5ff8)
[    4.614103] 5fa0:                                     00000000 00000000 00000000 00000000
[    4.614103] 5fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    4.614103] 5fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[    4.614103] ---[ end trace 25aee1320d92f42a ]---
[    4.808683] dmtimer posted=0
[    4.874143] Console: switching to colour frame buffer device 160x45
[    6.033079] omapdrm omapdrm.0: fb0: omapdrmdrmfb frame buffer device
[    6.050291] [drm] Initialized omapdrm 1.0.0 20110917 for omapdrm.0 on minor 0
[    6.064237] wwan_on_off_probe: wwan_on_off_probe()
[    6.075010] modem_vbus_hdmi_power: supplied by vsys
[    6.085674] modem_vbus_power: supplied by modem_vbus_hdmi_power
[    6.097624] wwan_on_off_probe: onoff = 95e4abce indicator = ed3fed02 -304227776 usb_phy = -1054427720
[    6.112933] wwan_on_off_probe: wwan_on_off_probe() wwan=62380c70
[    6.124723] wwan_on_off_is_powered_on: gpio value = 0
[    6.135374] wwan_on_off_is_powered_on: return 'false'
[    6.146146] wwan_on_off_rfkill_set_block: blocked: 1
[    6.156553] wwan_on_off_set_power:on = 0
[    6.165800] wwan_on_off_is_powered_on: gpio value = 0
[    6.176176] wwan_on_off_is_powered_on: return 'false'
[    6.186430] wwan_on_off_set_power: state 0
[    6.195646] wwan_on_off_set_power: regulator 0
[    6.205045] wwan_on_off_set_power: done
[    6.213865] wwan_on_off_probe: successfully probed
[    6.223905] otg_path: supplied by otg
[    6.232969] dwc3 4a030000.dwc3: Failed to get clk 'ref': -2
[    6.244505] dwc3 4a030000.dwc3: changing max_speed on rev 5533202a
[    6.257017] input: user-buttons as /devices/platform/user-buttons/input/input6
[    6.271757] input: pyra-game-buttons as /devices/platform/pyra-game-buttons/input/input7
[    6.289121] input: pyra-lid-wakeup as /devices/platform/pyra-lid-wakeup/input/input8
[    6.304258] palmas-rtc 48070000.i2c:palmas@48:rtc: setting system clock to 2021-06-09T11:05:43 UTC (1623236743)
[    6.319608] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    6.333708] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    6.345256] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    6.351221] l4sec_cm:clk:0038:0: failed to disable
[    6.359269] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db
[    6.368803] ALSA device list:
[    6.389083]   #0: HDMI 58040000.encoder
[    6.399265] Freeing unused kernel memory: 2048K
[    6.457335] Run /init as init process
[    6.491836]   with arguments:
[    6.507270]     /init
[    6.515989]     earlyprintk
[    6.524066]     fastboot
[    6.531839]   with environment:
[    6.540199]     HOME=/
[    6.547514]     TERM=linux
[    6.555112]     vram=12M
[    6.641050] set_switch() to 0
[    7.135862] drm_setup_crtcs_fb: sw_rotations=1
[    7.144132] drm_setup_crtcs_fb: fbcon_rotate_hint=0
[    7.219145] ehci-omap: OMAP-EHCI Host Controller driver
[    7.305814] ehci-omap 4a064c00.ehci: EHCI Host Controller
[    7.320342] ehci-omap 4a064c00.ehci: new USB bus registered, assigned bus number 1
[    7.325325] etnaviv etnaviv: bound 59000000.bb2d (ops gpu_ops [etnaviv])
[    7.350179] ehci-omap 4a064c00.ehci: irq 106, io mem 0x4a064c00
[    7.362626] pvrsrvkm 56000000.gpu: Enabling quirks 00000000
[    7.372499] cfg80211: failed to load regulatory.db
[    7.382810] [drm] Initialized pvr 1.14.3699939 20110701 for 56000000.gpu on minor 2
[    7.409238] etnaviv-gpu 59000000.bb2d: model: GC320, revision: 5301
[    7.424804] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1
[    7.437476] mmc0: new high speed MMC card at address 0001
[    7.447875] ehci-omap 4a064c00.ehci: USB 2.0 started, EHCI 1.00
[    7.470240] mmcblk0: mmc0:0001 HBG4a2 29.1 GiB 
[    7.481443] mmcblk0boot0: mmc0:0001 HBG4a2 partition 1 4.00 MiB
[    7.492033] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.06
[    7.505064] mmcblk0boot1: mmc0:0001 HBG4a2 partition 2 4.00 MiB
[    7.515653] mmcblk0rpmb: mmc0:0001 HBG4a2 partition 3 4.00 MiB, chardev (245:0)
[    7.527433] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    7.540067] usb usb1: Product: EHCI Host Controller
[    7.549559] usb usb1: Manufacturer: Linux 5.6.19-daveiii-pyradef-aufs ehci_hcd
[    7.561383]  mmcblk0: p1 p2
[    7.569547] usb usb1: SerialNumber: 4a064c00.ehci
[    7.580015] hub 1-0:1.0: USB hub found
[    7.588834] hub 1-0:1.0: 3 ports detected
[    7.965818] usb 1-2: new high-speed USB device number 2 using ehci-omap
[    8.068205] ehci-omap 4a064c00.ehci: port 2 reset error -110
[    8.450163] process '/usr/bin/fstype' started with executable stack
[    8.553526] F2FS-fs (mmcblk0p2): recover fsync data on readonly fs
[    8.606443] F2FS-fs (mmcblk0p2): Mounted with checkpoint version = 69ac88ab
[    8.808198] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist.
[    9.057645] ehci-omap 4a064c00.ehci: port 2 reset error -110
[    9.141752] systemd[1]: Inserted module 'autofs4'
[    9.187528] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[    9.222720] systemd[1]: Detected architecture arm.
[    9.306730] systemd[1]: Set hostname to <pyra-handheld>.
[    9.579184] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[    9.608488] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[    9.770330] systemd[1]: /lib/systemd/system/dbpd.service:6: PIDFile= references path below legacy directory /var/run/, updating /var/run/dbpd.pid → /run/dbpd.pid; please update the unit file accordingly.
[    9.838892] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[    9.855681] systemd[1]: Created slice system-getty.slice.
[    9.872627] systemd[1]: Created slice User and Session Slice.
[    9.892137] systemd[1]: Reached target Slices.
[    9.957395] ehci-omap 4a064c00.ehci: port 2 reset error -110
[   10.289793] RPC: Registered named UNIX socket transport module.
[   10.289795] RPC: Registered udp transport module.
[   10.289800] RPC: Registered tcp transport module.
[   10.289805] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   10.837309] ehci-omap 4a064c00.ehci: port 2 reset error -110
[   10.853187] systemd-journald[1853]: Received request to flush runtime journal from PID 1
[   11.714536] bmg160_i2c 2-0069: mounting matrix not found: using identity...
[   11.737333] ehci-omap 4a064c00.ehci: port 2 reset error -110
[   11.825351] bmg160_i2c 2-0069: Error reading reg_chip_id
[   11.841537] bmg160_i2c: probe of 2-0069 failed with error -121
[   11.902492] Bluetooth: Core ver 2.22
[   11.919432] NET: Registered protocol family 31
[   11.932249] Bluetooth: HCI device and connection manager initialized
[   11.943146] Bluetooth: HCI socket layer initialized
[   11.995937] Bluetooth: L2CAP socket layer initialized
[   12.005333] Bluetooth: SCO socket layer initialized
[   12.009519] input: twl6040:vibrator as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48070000.target-module/48070000.i2c/i2c-0/0-004b/twl6040-vibra/input/input9
[   12.095823] ina2xx 1-004f: power monitor ina231 (Rshunt = 20000 uOhm)
[   12.144665] Bluetooth: HCI UART driver ver 2.3
[   12.164976] input input3: as5013_open
[   12.225858] Bluetooth: HCI UART protocol H4 registered
[   12.246004] gpio gpiochip10: (4-0022): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[   12.296842] Bluetooth: HCI UART protocol BCSP registered
[   12.299894] input input2: as5013_open
[   12.308015] Bluetooth: HCI UART protocol LL registered
[   12.353666] Bluetooth: HCI UART protocol Broadcom registered
[   12.360243] gpio gpiochip10: (4-0022): unable to lock HW IRQ 14 for IRQ
[   12.378684] genirq: Failed to request resources for TS3A227E (irq 197) on irqchip 4-0022
[   12.404539] Bluetooth: hci0: change remote baud rate command in firmware
[   12.417063] usb usb1-port2: Cannot enable. Maybe the USB cable is bad?
[   12.420988] ts3a227e 4-003b: Cannot request irq 197 (-5)
[   12.507345] ehci-omap 4a064c00.ehci: port 2 reset error -110
[   12.582451] input input3: as5013_open
[   12.642423] input input2: as5013_open
[   12.711179] ts3a227e: probe of 4-003b failed with error -5
[   13.113828] EXT4-fs (mmcblk0p1): warning: mounting unchecked fs, running e2fsck is recommended
[   13.147669] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null)
[   13.163023] ext4 filesystem being mounted at /boot supports timestamps until 2038 (0x7fffffff)
[   13.207433] emif_probe: error getting device data
[   13.207487] emif_probe: error getting device data
[   13.291959] emif_probe: error getting device data
[   13.292012] emif_probe: error getting device data
[   13.487357] ehci-omap 4a064c00.ehci: port 2 reset error -110
[   13.715513] asoc-simple-card sound_bluetooth: W2CBW003 <-> 40122000.mcbsp mapping ok
[   13.910374] snd_soc_omap_abe_twl6040: unknown parameter 'index' ignored
[   13.944944] asoc-simple-card sound_fmradio: W2CBW003 <-> 40124000.mcbsp mapping ok
[   14.039243] asoc-simple-card sound_telephony: gtm601 <-> 40126000.mcbsp mapping ok
[   14.085722] omap-abe-twl6040 sound: ASoC: unknown pin AFML
[   14.151670] omap-abe-twl6040 sound: ASoC: unknown pin AFMR
[   14.253507] omap-abe-twl6040 sound: twl6040-legacy <-> 40132000.mcpdm mapping ok
[   14.261747] input: Letux Cortex 15 Headset Jack as /devices/platform/sound/sound/card4/input10
[   14.367305] ehci-omap 4a064c00.ehci: port 2 reset error -110
[   14.770628] wl18xx_driver wl18xx.2.auto: Direct firmware load for ti-connectivity/wl18xx-conf.bin failed with error -2
[   14.770628] wl18xx_driver wl18xx.2.auto: Falling back to sysfs fallback for: ti-connectivity/wl18xx-conf.bin
[   14.862875] wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin: -11
[   14.862882] wlcore: WARNING falling back to default config
[   15.247367] ehci-omap 4a064c00.ehci: port 2 reset error -110
[   15.376565] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)
[   15.383273] wlcore: WARNING Detected unconfigured mac address in nvs, derive from fuse instead.
[   15.383282] wlcore: WARNING This default nvs file can be removed from the file system
[   15.384763] wlcore: loaded
[   15.571412] PVR_K: UM DDK-(3699939) and KM DDK-(3699939) match. [ OK ]
[   16.127317] ehci-omap 4a064c00.ehci: port 2 reset error -110
[   16.177702] wwan_on_off_rfkill_set_block: blocked: 0
[   16.177705] wwan_on_off_set_power:on = 1
[   16.177714] wwan_on_off_is_powered_on: gpio value = 0
[   16.177720] wwan_on_off_is_powered_on: return 'false'
[   16.177725] wwan_on_off_set_power: state 0
[   16.177732] wwan_on_off_set_power: regulator 0
[   16.307161] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   16.307186] Bluetooth: BNEP socket layer initialized
[   16.568293] input input2: as5013_open
[   16.572691] input input3: as5013_open
[   16.785795] usb usb1-port2: Cannot enable. Maybe the USB cable is bad?
[   16.785825] usb usb1-port2: attempt power cycle
[   18.679960] wwan_on_off_set_power: send impulse
[   19.416085] wwan_on_off_is_powered_on: gpio value = 1
[   19.421435] wwan_on_off_is_powered_on: return 'true'
[   19.427610] wwan_on_off_set_power: done
[   19.432737] input: pyraInput keyboard as /devices/virtual/input/input11
[   19.433134] wwan_on_off_rfkill_set_block: blocked: 0
[   19.449448] input: pyraInput Gamepad as /devices/virtual/input/input12
[   19.455968] wwan_on_off_set_power:on = 1
[   19.461235] wwan_on_off_is_powered_on: gpio value = 1
[   19.467626] wwan_on_off_is_powered_on: return 'true'
[   19.472860] wwan_on_off_set_power: state 1
[   19.478274] wwan_on_off_set_power: regulator 1
[   19.483366] input: pyraInput Mouse as /devices/virtual/input/input13
[   19.489378] wwan_on_off_set_power: done
[   20.344572] wlcore: PHY firmware version: Rev 8.2.0.0.242
[   20.449277] wlcore: firmware booted (Rev 8.9.0.0.79)
[   20.470599] wlcore: down
[   20.942106] wlcore: PHY firmware version: Rev 8.2.0.0.242
[   21.060728] wlcore: firmware booted (Rev 8.9.0.0.79)
[   23.223005] fuse: init (API version 7.31)
[   25.666909] wlcore: down
[   29.825590] wlan0: authenticate with e0:22:04:22:8d:9a
[   29.837651] wlan0: send auth to e0:22:04:22:8d:9a (try 1/3)
[   29.875608] wlan0: authenticated
[   29.896756] wlan0: associate with e0:22:04:22:8d:9a (try 1/3)
[   29.907951] wlan0: RX AssocResp from e0:22:04:22:8d:9a (capab=0x511 status=0 aid=80)
[   29.933263] wlan0: associated
[   30.144929] wlan0: Limiting TX power to 127 (127 - 0) dBm as advertised by e0:22:04:22:8d:9a
[   30.288053] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   30.303220] wlcore: Association completed.
[   31.351099] Bluetooth: RFCOMM socket layer initialized
[   31.357175] Bluetooth: RFCOMM ver 1.11
[   36.726629] wlcore: WARNING no fw rx ba on tid 5
[   36.965820] host1_vbus_power: supplied by modem_vbus_hdmi_power
[   36.972934] host2_vbus_power: supplied by modem_vbus_hdmi_power
[   36.985893] ldo3: disabling
[   36.995154] ldo8: disabling
[   37.002668] otg_path: disabling

 

[EvilDragon]

You inserted the device AFTER it has fully booted, right?
Would be weird if nothing happens in that case.. but okay

 

[ingoreis]

Oh i thought i have to activate my USB Ports on my Pyra like the Pandora.
I have a Similiar Problem then.
No USB Stick from mine did work..then i simply used a SD Card and thought not much about that.

I will test it this Evening again and will report my DMESG Messages too.

Thought it was simply not implemented in the OS now or i somehow have to acticate my USB Ports.

My USB3 OTG Adapter did not work too with a normal USB Dongle.

This Evening i will test more and report more.

 

[Kazuki]

Yes that was after it was booted.

 

[Bosbeetle]

I have a Similiar Problem then.

it's definetly not normal, I tried three USB memory sticks and all three worked.

 

[EvilDragon]

it's definetly not normal, I tried three USB memory sticks and all three worked.

All the time? I tried 5 boots on a unit I have here today, and 3 times USB worked fine, 2 times it didn't.

 

[Bosbeetle]

All the time? I tried 5 boots on a unit I have here today, and 3 times USB worked fine, 2 times it didn't.

Will try ten consequtive boots, Ill report back!

 

[Bosbeetle]

So then boots, than after boot inserted USB stick and watched if drive was mounted, copied a small file from stick to home directory, ejected the USB and shutdown and reboot.
This is 30 consequetive reboots in total but three ports tested.

black USB port - 8/10 two fails showing port 2 reset error -110 in dmesg
blue USB port - 6/10 four fails
USB3 port = 10/10 no fails

dmesg when usb failes:

Spoiler

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.6.19-daveiii-pyradef-aufs (pyra@debian-buster) (gcc version 8.3.0 (Debian 8.3.0-2)) #3 SMP PREEMPT Mon Dec 14 18:23:52 CET 2020
[ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Pyra-Handheld-V5.3
[ 0.000000] printk: debug: ignoring loglevel setting.
[ 0.000000] printk: debug: ignoring loglevel setting.
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 64 MiB at 0x00000000fb000000
[ 0.000000] OMAP4: Map 0x00000000afd00000 to (ptrval) for dram barrier
[ 0.000000] On node 0 totalpages: 1043712
[ 0.000000] DMA zone: 2295 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 195840 pages, LIFO batch:63
[ 0.000000] HighMem zone: 847872 pages, LIFO batch:63
[ 0.000000] OMAP5432 ES2.0
[ 0.000000] percpu: Embedded 20 pages/cpu s50316 r8192 d23412 u81920
[ 0.000000] pcpu-alloc: s50316 r8192 d23412 u81920 alloc=20*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1041417
[ 0.000000] Kernel command line: root=PARTUUID=947d8093-02 console=ttyO2,115200n8 console=tty0 vram=12M omapfb.vram=0:8M,1:4M omapfb.rotate_type=0 omapdss.def_disp=lcd rootwait twl4030_charger.allow_usb=1 musb_hdrc.preserve_vbus=1 log_buf_len=8M ignore_loglevel earlyprintk drm_kms_helper.fbdev_rotation=8 drm.force_hw_rotation fastboot coherent_pool=1M twl4030_charger.allow_usb=1 fsck.repair=yes rootfstype=f2fs rootwait ignore_loglevel
[ 0.000000] printk: log_buf_len: 8388608 bytes
[ 0.000000] printk: early log buf free: 63724(97%)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stackff, heap allocff, heap freeff
[ 0.000000] software IO TLB: mapped [mem 0xa53bf000-0xa93bf000] (64MB)
[ 0.000000] Memory: 3948468K/4174848K available (10478K kernel code, 908K rwdata, 2772K rodata, 2048K init, 269K bss, 160844K reserved, 65536K cma-reserved, 3325952K highmem)
[ 0.000000] random: get_random_u32 called from __kmem_cache_create+0x34/0x4f8 with crng_init=0
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] OMAP clockevent source: timer1 at 32768 Hz
[ 0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16ac02862, max_idle_ns: 440795202218 ns
[ 0.000010] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511085ns
[ 0.000032] Switching to timer-based delay loop, resolution 162ns
[ 0.000164] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[ 0.000179] OMAP clocksource: 32k_counter at 32768 Hz
[ 0.002035] Console: colour dummy device 80x30
[ 0.002993] printk: console [tty0] enabled
[ 0.003062] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.28 BogoMIPS (lpj=61440)
[ 0.003113] pid_max: default: 32768 minimum: 301
[ 0.003402] LSM: Security Framework initializing
[ 0.003535] Yama: becoming mindful.
[ 0.003716] AppArmor: AppArmor initialized
[ 0.003754] TOMOYO Linux initialized
[ 0.003874] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.003920] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.005190] CPU: Testing write buffer coherency: ok
[ 0.005273] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[ 0.005734] /cpus/cpu@0 missing clock-frequency property
[ 0.005793] /cpus/cpu@1 missing clock-frequency property
[ 0.005827] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.059695] Setting up static identity map for 0x80200000 - 0x80200060
[ 0.079704] rcu: Hierarchical SRCU implementation.
[ 0.119745] smp: Bringing up secondary CPUs ...
[ 0.200086] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.200100] CPU1: Spectre v2: using ICIALLU workaround
[ 0.200229] smp: Brought up 1 node, 2 CPUs
[ 0.200245] SMP: Total of 2 processors activated (24.57 BogoMIPS).
[ 0.200259] CPU: All CPU(s) started in HYP mode.
[ 0.200269] CPU: Virtualization extensions available.
[ 0.200717] devtmpfs: initialized
[ 0.215060] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[ 0.215516] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.215545] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.216861] pinctrl core: initialized pinctrl subsystem
[ 0.217685] thermal_sys: Registered thermal governor 'fair_share'
[ 0.217685] thermal_sys: Registered thermal governor 'step_wise'
[ 0.217702] thermal_sys: Registered thermal governor 'user_space'
[ 0.218573] NET: Registered protocol family 16
[ 0.221129] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.222113] omap_hwmod: l3_main_3 using broken dt data from ocp
[ 0.222934] omap_hwmod: l3_main_2 using broken dt data from ocp
[ 0.235995] audit: initializing netlink subsys (disabled)
[ 0.236208] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1
[ 0.239906] cpuidle: using governor menu
[ 0.266176] platform 50000000.gpmc: Cannot lookup hwmod 'gpmc'
[ 0.266360] omap-gpmc 50000000.gpmc: _od_fail_runtime_resume: FIXME: missing hwmod/omap_dev info
[ 0.266391] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[ 0.275058] No ATAGs?
[ 0.275119] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.275149] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.296916] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.303561] vsys_cobra: supplied by vmain
[ 0.307787] iommu: Default domain type: Translated
[ 0.310031] vgaarb: loaded
[ 0.310672] SCSI subsystem initialized
[ 0.314252] libata version 3.00 loaded.
[ 0.314761] usbcore: registered new interface driver usbfs
[ 0.314853] usbcore: registered new interface driver hub
[ 0.314980] usbcore: registered new device driver usb
[ 0.315280] usb_phy_generic hsusb2_phy: hsusb2_phy supply vcc not found, using dummy regulator
[ 0.317080] Advanced Linux Sound Architecture Driver Initialized.
[ 0.317752] NetLabel: Initializing
[ 0.317764] NetLabel: domain hash size = 128
[ 0.317782] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.317843] NetLabel: unlabeled traffic allowed by default
[ 0.318637] clocksource: Switched to clocksource arch_sys_counter
[ 0.384616] VFS: Disk quotas dquot_6.6.0
[ 0.384679] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.385318] AppArmor: AppArmor Filesystem Enabled
[ 0.397006] NET: Registered protocol family 2
[ 0.397495] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.397545] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.397616] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.397760] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.397860] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.397891] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.398104] NET: Registered protocol family 1
[ 0.398547] PCI: CLS 0 bytes, default 64
[ 0.399081] Trying to unpack rootfs image as initramfs...
[ 1.260766] Freeing initrd memory: 18852K
[ 1.261294] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[ 1.261510] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[ 1.263861] Initialise system trusted keyrings
[ 1.264010] workingset: timestamp_bits=14 max_order=20 bucket_order=6
[ 1.274327] zbud: loaded
[ 1.282691] jitterentropy: Initialization failed with host not compliant with requirements: 2
[ 1.282718] Key type asymmetric registered
[ 1.282739] Asymmetric key parser 'x509' registered
[ 1.282779] bounce: pool size: 64 pages
[ 1.282895] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.282908] io scheduler mq-deadline registered
[ 1.282931] io scheduler kyber registered
[ 1.288610] OMAP GPIO hardware version 0.1
[ 1.313479] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
[ 1.386447] GPIO line 74 (gpio8_234/msecure) hogged as output/high
[ 1.414358] ti-pipe3 4a096000.phy: can't get syscon-pllreset, sata dpll won't idle
[ 1.415917] pinctrl-single 4ae0c840.pinmux: 30 pins, size 60
[ 1.416579] pinctrl-single 4a002840.pinmux: 219 pins, size 438
[ 1.420801] pwm-backlight keyboard-backlight: keyboard-backlight supply power not found, using dummy regulator
[ 1.421095] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[ 1.426059] ti_abb 4ae07cdc.regulator-abb-mpu: can't request region for resource [mem 0x4ae07cdc-0x4ae07ce3]
[ 1.426089] ti_abb: probe of 4ae07cdc.regulator-abb-mpu failed with error -16
[ 1.426150] ti_abb 4ae07ce4.regulator-abb-mm: can't request region for resource [mem 0x4ae07ce4-0x4ae07ceb]
[ 1.426181] ti_abb: probe of 4ae07ce4.regulator-abb-mm failed with error -16
[ 1.426666] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.429507] 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 108, base_baud = 3000000) is a OMAP UART2
[ 2.388913] printk: console [ttyO2] enabled
[ 2.393985] omap_uart 48068000.serial: no wakeirq for uart5
[ 2.400058] 48068000.serial: ttyO5 at MMIO 0x48068000 (irq = 121, base_baud = 3000000) is a OMAP UART5
[ 2.410549] omap_uart 4806c000.serial: no wakeirq for uart1
[ 2.416598] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 122, base_baud = 3000000) is a OMAP UART1
[ 2.426672] serial serial0: tty port ttyO1 registered
[ 2.432199] omap_uart 4806e000.serial: no wakeirq for uart3
[ 2.438263] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 123, base_baud = 3000000) is a OMAP UART3
[ 2.450076] omap_rng 48090000.rng: Random Number Generator ver. 20
[ 2.450621] random: fast init done
[ 2.457339] omapdss_dss 58000000.dss: 58000000.dss supply vdda_video not found, using dummy regulator
[ 2.460371] random: crng init done
[ 2.473760] DSS: OMAP DSS rev 6.1
[ 2.491345] brd: module loaded
[ 2.499606] loop: module loaded
[ 2.502924] wwan_on_off_init: wwan_on_off_init
[ 2.508025] wwan_on_off_probe: wwan_on_off_probe()
[ 2.515414] ahci 4a140000.sata: 4a140000.sata supply ahci not found, using dummy regulator
[ 2.524212] ahci 4a140000.sata: 4a140000.sata supply phy not found, using dummy regulator
[ 2.532992] ahci 4a140000.sata: 4a140000.sata supply target not found, using dummy regulator
[ 2.542086] ahci 4a140000.sata: SSS flag set, parallel bus scan disabled
[ 2.549197] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 2.558200] ahci 4a140000.sata: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part ccc apst
[ 2.569095] scsi host0: ahci
[ 2.572574] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 31
[ 2.581485] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 2.590030] libphy: Fixed MDIO Bus: probed
[ 2.597873] omap-dwc3 4a020000.omap_dwc3: vbus init failed
[ 2.604015] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.610950] ehci-pci: EHCI PCI platform driver
[ 2.615735] usbcore: registered new interface driver usb-storage
[ 2.622714] mousedev: PS/2 mouse device common for all mice
[ 2.630168] i2c /dev entries driver
[ 2.633945] IR NEC protocol handler initialized
[ 2.638736] IR RC5(x/sz) protocol handler initialized
[ 2.644063] IR RC6 protocol handler initialized
[ 2.648867] IR JVC protocol handler initialized
[ 2.653640] IR Sony protocol handler initialized
[ 2.658528] IR SANYO protocol handler initialized
[ 2.663516] IR Sharp protocol handler initialized
[ 2.668477] IR MCE Keyboard/mouse protocol handler initialized
[ 2.674655] IR XMP protocol handler initialized
[ 2.679446] Driver for 1-wire Dallas network protocol.
[ 2.689242] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[ 2.698825] sdhci: Secure Digital Host Controller Interface driver
[ 2.705342] sdhci: Copyright(c) Pierre Ossman
[ 2.710910] omap_gpio 48053000.gpio: Could not set line 4 debounce to 200000 microseconds (-22)
[ 2.720096] omap_hsmmc 4809c000.mmc: Got CD GPIO
[ 2.724978] omap_hsmmc 4809c000.mmc: Got WP GPIO
[ 2.765089] omap_gpio 48057000.gpio: Could not set line 13 debounce to 200000 microseconds (-22)
[ 2.774439] omap_hsmmc 480d1000.mmc: Got CD GPIO
[ 2.779452] omap_hsmmc 480d1000.mmc: Got WP GPIO
[ 2.789087] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.795779] txs02612 txs02612: probe
[ 2.799656] txs02612 txs02612: failed to get mmc phandle in /txs02612 node
[ 2.806954] txs02612 txs02612: could not get access to host port, using manual mode
[ 2.838697] txs02612_request: current=1 client=0
[ 2.868686] txs02612 txs02612: probed
[ 2.872653] txs02612_request: current=0 client=1
[ 2.877963] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.887382] usbcore: registered new interface driver usbhid
[ 2.893313] usbhid: USB HID core driver
[ 2.897676] ashmem: initialized
[ 2.908112] oprofile: using timer interrupt.
[ 2.912698] drop_monitor: Initializing network drop monitor service
[ 2.916249] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.920382] NET: Registered protocol family 10
[ 2.955783] Segment Routing with IPv6
[ 2.959781] mip6: Mobile IPv6
[ 2.962918] NET: Registered protocol family 17
[ 2.967624] mpls_gso: MPLS GSO support
[ 2.971973] ThumbEE CPU extension supported.
[ 2.976500] Registering SWP/SWPB emulation handler
[ 2.981613] omap_vc_init_channel: No PMIC info for vdd_core
[ 2.987509] omap_vp_init: No PMIC info for vdd_core
[ 2.992709] omap_vc_init_channel: No PMIC info for vdd_mm
[ 2.998403] omap_vp_init: No PMIC info for vdd_mm
[ 3.003421] omap_vc_init_channel: No PMIC info for vdd_mpu
[ 3.009242] omap_vp_init: No PMIC info for vdd_mpu
[ 3.014302] Power Management for TI OMAP4+ devices.
[ 3.020144] Loading compiled-in X.509 certificates
[ 3.029147] Loaded X.509 cert 'Build time autogenerated kernel key: 4020818a539cdd7ae890874388bde6caf4fc6257'
[ 3.040122] Key type ._fscrypt registered
[ 3.044364] Key type .fscrypt registered
[ 3.048513] Key type fscrypt-provisioning registered
[ 3.054029] AppArmor: AppArmor sha1 policy hashing enabled
[ 3.080905] dmm 4e000000.dmm: initialized all PAT entries
[ 3.090670] omap-iommu 4a066000.mmu: 4a066000.mmu registered
[ 3.098178] bmc150_accel_i2c 2-0010: mounting matrix not found: using identity...
[ 3.132327] bmc150_accel_i2c 2-0010: Error: Reading chip id
[ 3.138278] bmc150_accel_i2c: probe of 2-0010 failed with error -121
[ 3.145419] bmc150_magn_i2c 2-0012: mounting matrix not found: using identity...
[ 3.153507] bmc150_magn_i2c 2-0012: Failed to bring up device from suspend mode
[ 3.161377] bmc150_magn_i2c: probe of 2-0012 failed with error -121
[ 3.168316] bmp280 2-0077: 2-0077 supply vddd not found, using dummy regulator
[ 3.176028] bmp280 2-0077: 2-0077 supply vdda not found, using dummy regulator
[ 3.194888] bmp280: probe of 2-0077 failed with error -121
[ 3.201015] bmp280 2-0076: 2-0076 supply vddd not found, using dummy regulator
[ 3.208701] bmp280 2-0076: 2-0076 supply vdda not found, using dummy regulator
[ 3.229281] bno055 2-0029: mounting matrix not found: using identity...
[ 3.244967] bno055 2-0029: software revision id 0311
[ 3.252804] input: iio-bridge: bno055 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48060000.target-module/48060000.i2c/i2c-2/2-0029/iio:device1/input/input0
[ 3.271853] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz
[ 3.278784] palmas 0-0048: Irq flag is 0x00000008
[ 3.315535] palmas 0-0048: Muxing GPIO 3, PWM 0, LED 0
[ 3.332699] palmas-rtc 48070000.i2calmas@48:rtc: registered as rtc0
[ 3.344925] SMPS123: supplied by regulator-dummy
[ 3.352468] SMPS45: supplied by regulator-dummy
[ 3.358846] SMPS6: supplied by vsys_cobra
[ 3.364413] SMPS7: supplied by vsys_cobra
[ 3.370173] SMPS8: supplied by vsys_cobra
[ 3.375826] SMPS9: supplied by vsys_cobra
[ 3.380587] smps9: Bringing 0uV into 2100000-2100000uV
[ 3.387766] SMPS10_OUT2: supplied by regulator-dummy
[ 3.394518] SMPS10_OUT1: supplied by regulator-dummy
[ 3.401339] LDO1: supplied by vsys_cobra
[ 3.405887] ldo1: Bringing 0uV into 1800000-1800000uV
[ 3.414353] LDO2: supplied by vsys_cobra
[ 3.419101] ldo2: Bringing 0uV into 1800000-1800000uV
[ 3.428023] ldo4: Bringing 0uV into 1800000-1800000uV
[ 3.435611] LDO5: supplied by vsys_cobra
[ 3.445620] LDO7: supplied by vsys_cobra
[ 3.450320] ldo7: Bringing 0uV into 2000000-2000000uV
[ 3.458693] LDO8: supplied by vsys_cobra
[ 3.466342] LDO9: supplied by vmmcsd_fixed
[ 3.475680] LDOLN: supplied by vsys_cobra
[ 3.482166] LDOUSB: supplied by vsys_cobra
[ 3.491424] palmas_pwrbutton 48070000.i2calmas@48almas_power_button: h/w controlled shutdown duration=8 seconds
[ 3.505648] input: palmas_pwron as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48070000.target-module/48070000.i2c/i2c-0/0-0048/48070000.i2calmas@48almas_power_button/input/input1
[ 3.530732] usb3503 0-0008: usb3503_probe
[ 3.538693] usb3503 0-0008: reset gpio state 1
[ 3.543391] usb3503 0-0008: usb3503_connect
[ 3.547813] usb3503 0-0008: usb3503_reset 1
[ 3.558759] usb3503 0-0008: SP_ILOCK failed (-121)
[ 3.563834] usb3503 0-0008: usb3503_probe: probed in hub mode
[ 3.570193] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
[ 3.599713] as5013 1-0040: ID code: 0c
[ 3.604342] as5013 1-0040: ID version: 0d
[ 3.609042] as5013 1-0040: silicon revision: 00
[ 3.614404] as5013 1-0040: control: f1
[ 3.618502] input: nub0 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48072000.target-module/48072000.i2c/i2c-1/1-0040/input/input2
[ 3.635104] as5013 1-0040: probe 40, gpio -2, irq 0, "as5013"
[ 3.642057] as5013 1-0041: ID code: 0c
[ 3.646670] as5013 1-0041: ID version: 0d
[ 3.651412] as5013 1-0041: silicon revision: 00
[ 3.656863] as5013 1-0041: control: f1
[ 3.661041] input: nub1 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48072000.target-module/48072000.i2c/i2c-1/1-0041/input/input3
[ 3.677645] as5013 1-0041: probe 41, gpio -2, irq 0, "as5013"
[ 3.687167] input: tca8418 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48072000.target-module/48072000.i2c/i2c-1/1-0034/input/input4
[ 3.704287] bq27xxx_battery_setup
[ 3.707789] bq27xxx_battery_setup: dm_regs=edca2703
[ 3.713382] bq27xxx_battery_settings
[ 3.717166] bq27xxx_battery_set_config
[ 3.721133] bq27xxx_battery_unseal
[ 3.735235] bq27xxx_battery_update_dm_block
[ 3.739657] bq27xxx-battery 1-0055: design-capacity has 6000
[ 3.745626] bq27xxx_battery_update_dm_block
[ 3.750064] bq27xxx-battery 1-0055: design-energy has 22200
[ 3.755934] bq27xxx_battery_update_dm_block
[ 3.760386] bq27xxx-battery 1-0055: terminate-voltage has 3200
[ 3.766555] bq27xxx_battery_seal
[ 3.777771] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
[ 3.810000] input: TSC2007 Touchscreen as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/4807a000.target-module/4807a000.i2c/i2c-3/3-0048/input/input5
[ 3.829750] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
[ 3.837268] vdds_1v8_main: supplied by smps7
[ 3.842624] pca953x 4-0022: using AI
[ 3.873553] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz
[ 3.881308] omap-iommu 55082000.mmu: 55082000.mmu registered
[ 3.889401] pwm-backlight keyboard-backlight: keyboard-backlight supply power not found, using dummy regulator
[ 3.900291] dmtimer posted=0
[ 3.903685] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[ 3.913342] ldo4: supplied by vdds_1v8_main
[ 3.924685] wwan_on_off_probe: wwan_on_off_probe()
[ 3.930972] omap-dwc3 4a020000.omap_dwc3: vbus init failed
[ 3.940402] omap_gpio 48053000.gpio: Could not set line 4 debounce to 200000 microseconds (-22)
[ 3.949618] omap_hsmmc 4809c000.mmc: Got CD GPIO
[ 3.954532] omap_hsmmc 4809c000.mmc: Got WP GPIO
[ 3.994510] omap_hsmmc 480ad000.mmc: allocated mmc-pwrseq
[ 4.073977] mmc3: new high speed SDXC card at address aaaa
[ 4.090785] mmcblk3: mmc3:aaaa SF128 119 GiB
[ 4.099063] mmcblk3: p1
[ 4.115481] omap_gpio 48057000.gpio: Could not set line 13 debounce to 200000 microseconds (-22)
[ 4.124820] omap_hsmmc 480d1000.mmc: Got CD GPIO
[ 4.129763] omap_hsmmc 480d1000.mmc: Got WP GPIO
[ 4.141297] omap_hsmmc 480ad000.mmc: card claims to support voltages below defined range
[ 4.172245] mmc4: new high speed SDIO card at address 0001
[ 4.249185] ldo3: supplied by vdds_1v8_main
[ 4.253939] ldo6: supplied by vdds_1v8_main
[ 4.434970] mmc5: new high speed SDXC card at address aaaa
[ 4.452339] bq2429x_charger 1-006b: bq2429x_parse_dt,line=1539 chg_current = 2048000 usb_input_current = 3000000 adp_input_current = 2048000 bat_volt_max = 4200000
[ 4.468081] mmcblk5: mmc5:aaaa SR64G 59.5 GiB
[ 4.472974] bq2429x_charger 1-006b: found regulator-max-microvolt = 4200000
[ 4.482649] mmcblk5: p1
[ 4.488252] vsys: Bringing 3300000uV into 3500000-3500000uV
[ 4.499093] omapdss_dss 58000000.dss: bound 58001000.dispc (ops 0xc0ca350c)
[ 4.506521] omapdss_dss 58000000.dss: bound 58004000.encoder (ops 0xc0ca52d4)
[ 4.514680] omap-hdmi-audio omap-hdmi-audio.1.auto: snd-soc-dummy-dai <-> 58040000.encoder mapping ok
[ 4.524755] omapdss_dss 58000000.dss: bound 58040000.encoder (ops 0xc0ca6160)
[ 4.534427] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 4.541598] [drm] No driver support for vblank timestamp query.
[ 4.581088] drm_setup_crtcs_fb: sw_rotations=1
[ 4.585879] drm_setup_crtcs_fb: fbcon_rotate_hint=0
[ 4.597567] ------------[ cut here ]------------
[ 4.597598] WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x254/0x374
[ 4.597614] 44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4WAKEUP (Idle): Data Access in User mode during Functional access
[ 4.597625] Modules linked in:
[ 4.597635] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.19-daveiii-pyradef-aufs #3
[ 4.597648] Hardware name: Generic OMAP5 (Flattened Device Tree)
[ 4.597689] [<c0212e60>] (unwind_backtrace) from [<c020d1a0>] (show_stack+0x10/0x14)
[ 4.597699] [<c020d1a0>] (show_stack) from [<c0c1b544>] (dump_stack+0x94/0xa8)
[ 4.597720] [<c0c1b544>] (dump_stack) from [<c02351f0>] (__warn+0xd0/0xf8)
[ 4.597750] [<c02351f0>] (__warn) from [<c02355e0>] (warn_slowpath_fmt+0x94/0xb8)
[ 4.597771] [<c02355e0>] (warn_slowpath_fmt) from [<c064c23c>] (l3_interrupt_handler+0x254/0x374)
[ 4.597784] [<c064c23c>] (l3_interrupt_handler) from [<c0290864>] (__handle_irq_event_percpu+0x58/0x29c)
[ 4.597812] [<c0290864>] (__handle_irq_event_percpu) from [<c0290ad4>] (handle_irq_event_percpu+0x2c/0x80)
[ 4.597817] [<c0290ad4>] (handle_irq_event_percpu) from [<c0290b60>] (handle_irq_event+0x38/0x5c)
[ 4.597842] [<c0290b60>] (handle_irq_event) from [<c02950f4>] (handle_fasteoi_irq+0xb8/0x168)
[ 4.597858] [<c02950f4>] (handle_fasteoi_irq) from [<c028fae4>] (generic_handle_irq+0x24/0x34)
[ 4.597873] [<c028fae4>] (generic_handle_irq) from [<c02900b8>] (__handle_domain_irq+0x5c/0xb4)
[ 4.597889] [<c02900b8>] (__handle_domain_irq) from [<c064a570>] (gic_handle_irq+0x3c/0x78)
[ 4.597903] [<c064a570>] (gic_handle_irq) from [<c0201ab8>] (__irq_svc+0x58/0x8c)
[ 4.597911] Exception stack(0xc1201eb8 to 0xc1201f00)
[ 4.597931] 1ea0: 00000000 efc99f80
[ 4.597934] 1ec0: 00000001 c1200000 c120a1c8 c120a158 efc95a78 00000001 00000001 120910a0
[ 4.597950] 1ee0: 00000001 00000001 00000000 c1201f08 c02c13c4 c08ff5c4 200c0113 ffffffff
[ 4.597965] [<c0201ab8>] (__irq_svc) from [<c08ff5c4>] (cpuidle_enter_state+0x164/0x5b8)
[ 4.597995] [<c08ff5c4>] (cpuidle_enter_state) from [<c08ffa54>] (cpuidle_enter+0x28/0x38)
[ 4.598013] [<c08ffa54>] (cpuidle_enter) from [<c026781c>] (do_idle+0x234/0x29c)
[ 4.598025] [<c026781c>] (do_idle) from [<c0267b78>] (cpu_startup_entry+0x18/0x20)
[ 4.598056] [<c0267b78>] (cpu_startup_entry) from [<c100137c>] (start_kernel+0x7cc/0x810)
[ 4.598065] [<c100137c>] (start_kernel) from [<00000000>] (0x0)
[ 4.598086] ---[ end trace 95f6622d31b98ad7 ]---
[ 4.778998] dmtimer posted=0
[ 4.886935] Console: switching to colour frame buffer device 160x45
[ 5.300418] omapdrm omapdrm.0: fb0: omapdrmdrmfb frame buffer device
[ 5.317569] [drm] Initialized omapdrm 1.0.0 20110917 for omapdrm.0 on minor 0
[ 5.333895] wwan_on_off_probe: wwan_on_off_probe()
[ 5.347018] modem_vbus_hdmi_power: supplied by vsys
[ 5.357852] modem_vbus_power: supplied by modem_vbus_hdmi_power
[ 5.369998] wwan_on_off_probe: onoff = 4123958b indicator = 8e639c8c -304228288 usb_phy = -1054427720
[ 5.385498] wwan_on_off_probe: wwan_on_off_probe() wwan=98397ef9
[ 5.397769] wwan_on_off_is_powered_on: gpio value = 0
[ 5.408908] wwan_on_off_is_powered_on: return 'false'
[ 5.420047] wwan_on_off_rfkill_set_block: blocked: 1
[ 5.430666] wwan_on_off_set_powern = 0
[ 5.440065] wwan_on_off_is_powered_on: gpio value = 0
[ 5.450587] wwan_on_off_is_powered_on: return 'false'
[ 5.461059] wwan_on_off_set_power: state 0
[ 5.470401] wwan_on_off_set_power: regulator 0
[ 5.480014] wwan_on_off_set_power: done
[ 5.489021] wwan_on_off_probe: successfully probed
[ 5.499569] otg_path: supplied by otg
[ 5.508717] dwc3 4a030000.dwc3: Failed to get clk 'ref': -2
[ 5.522891] dwc3 4a030000.dwc3: changing max_speed on rev 5533202a
[ 5.535801] input: user-buttons as /devices/platform/user-buttons/input/input6
[ 5.552157] input: pyra-game-buttons as /devices/platform/pyra-game-buttons/input/input7
[ 5.569578] input: pyra-lid-wakeup as /devices/platform/pyra-lid-wakeup/input/input8
[ 5.584292] palmas-rtc 48070000.i2calmas@48:rtc: setting system clock to 2021-06-09T18:46:36 UTC (1623264396)
[ 5.599826] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 5.614413] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 5.625979] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 5.634026] l4sec_cm:clk:0038:0: failed to disable
[ 5.639926] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db
[ 5.649629] ALSA device list:
[ 5.670116] #0: HDMI 58040000.encoder
[ 5.680728] Freeing unused kernel memory: 2048K
[ 5.759357] Run /init as init process
[ 5.776278] with arguments:
[ 5.792300] /init
[ 5.798995] earlyprintk
[ 5.806122] fastboot
[ 5.813017] with environment:
[ 5.820498] HOME=/
[ 5.826999] TERM=linux
[ 5.834003] vram=12M
[ 5.932942] set_switch() to 0
[ 6.059583] mmc0: new high speed MMC card at address 0001
[ 6.078883] mmcblk0: mmc0:0001 HBG4a2 29.1 GiB
[ 6.087459] mmcblk0boot0: mmc0:0001 HBG4a2 partition 1 4.00 MiB
[ 6.102847] mmcblk0boot1: mmc0:0001 HBG4a2 partition 2 4.00 MiB
[ 6.116214] mmcblk0rpmb: mmc0:0001 HBG4a2 partition 3 4.00 MiB, chardev (245:0)
[ 6.132846] mmcblk0: p1 p2
[ 6.329501] drm_setup_crtcs_fb: sw_rotations=1
[ 6.337908] drm_setup_crtcs_fb: fbcon_rotate_hint=0
[ 6.632907] ehci-omap: OMAP-EHCI Host Controller driver
[ 6.725406] etnaviv etnaviv: bound 59000000.bb2d (ops gpu_ops [etnaviv])
[ 6.738986] ehci-omap 4a064c00.ehci: EHCI Host Controller
[ 6.759182] cfg80211: failed to load regulatory.db
[ 6.774173] etnaviv-gpu 59000000.bb2d: model: GC320, revision: 5301
[ 6.785006] ehci-omap 4a064c00.ehci: new USB bus registered, assigned bus number 1
[ 6.799092] ehci-omap 4a064c00.ehci: irq 106, io mem 0x4a064c00
[ 6.823191] pvrsrvkm 56000000.gpu: Enabling quirks 00000000
[ 6.836276] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1
[ 6.848695] ehci-omap 4a064c00.ehci: USB 2.0 started, EHCI 1.00
[ 6.859896] [drm] Initialized pvr 1.14.3699939 20110701 for 56000000.gpu on minor 2
[ 6.860281] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.06
[ 6.886081] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.900189] usb usb1: Product: EHCI Host Controller
[ 6.914615] usb usb1: Manufacturer: Linux 5.6.19-daveiii-pyradef-aufs ehci_hcd
[ 6.926110] usb usb1: SerialNumber: 4a064c00.ehci
[ 6.935492] hub 1-0:1.0: USB hub found
[ 6.943240] hub 1-0:1.0: 3 ports detected
[ 7.339006] usb 1-2: new high-speed USB device number 2 using ehci-omap
[ 7.451083] ehci-omap 4a064c00.ehci: port 2 reset error -110
[ 7.677498] process '/usr/bin/fstype' started with executable stack
[ 7.797006] F2FS-fs (mmcblk0p2): recover fsync data on readonly fs
[ 7.849704] F2FS-fs (mmcblk0p2): Mounted with checkpoint version = 21555952
[ 8.065371] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist.
[ 8.391238] systemd[1]: Inserted module 'autofs4'
[ 8.431701] ehci-omap 4a064c00.ehci: port 2 reset error -110
[ 8.447513] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 8.482669] systemd[1]: Detected architecture arm.
[ 8.558017] systemd[1]: Set hostname to <terminaalverdwaald>.
[ 8.882846] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[ 8.916904] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[ 9.063083] systemd[1]: /lib/systemd/system/dbpd.service:6: PIDFile= references path below legacy directory /var/run/, updating /var/run/dbpd.pid → /run/dbpd.pid; please update the unit file accordingly.
[ 9.140017] systemd[1]: Created slice system-getty.slice.
[ 9.153473] systemd[1]: Listening on Journal Audit Socket.
[ 9.172331] systemd[1]: Listening on Syslog Socket.
[ 9.192287] systemd[1]: Reached target Swap.
[ 9.320712] ehci-omap 4a064c00.ehci: port 2 reset error -110
[ 9.493228] RPC: Registered named UNIX socket transport module.
[ 9.493228] RPC: Registered udp transport module.
[ 9.493228] RPC: Registered tcp transport module.
[ 9.493232] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 9.966464] systemd-journald[1831]: Received request to flush runtime journal from PID 1
[ 10.200221] ehci-omap 4a064c00.ehci: port 2 reset error -110
[ 11.090237] ehci-omap 4a064c00.ehci: port 2 reset error -110
[ 11.132299] bmg160_i2c 2-0069: mounting matrix not found: using identity...
[ 11.251637] input: twl6040:vibrator as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48070000.target-module/48070000.i2c/i2c-0/0-004b/twl6040-vibra/input/input9
[ 11.285006] bmg160_i2c 2-0069: Error reading reg_chip_id
[ 11.313784] Bluetooth: Core ver 2.22
[ 11.366977] ina2xx 1-004f: power monitor ina231 (Rshunt = 20000 uOhm)
[ 11.419467] gpio gpiochip10: (4-0022): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[ 11.452670] bmg160_i2c: probe of 2-0069 failed with error -121
[ 11.504672] input input2: as5013_open
[ 11.534415] NET: Registered protocol family 31
[ 11.569796] input input3: as5013_open
[ 11.578541] Bluetooth: HCI device and connection manager initialized
[ 11.589996] Bluetooth: HCI socket layer initialized
[ 11.612982] Bluetooth: L2CAP socket layer initialized
[ 11.623149] Bluetooth: SCO socket layer initialized
[ 11.642844] gpio gpiochip10: (4-0022): unable to lock HW IRQ 14 for IRQ
[ 11.654587] genirq: Failed to request resources for TS3A227E (irq 197) on irqchip 4-0022
[ 11.674166] ts3a227e 4-003b: Cannot request irq 197 (-5)
[ 11.686752] ts3a227e: probe of 4-003b failed with error -5
[ 11.720623] input input2: as5013_open
[ 11.758883] usb usb1-port2: Cannot enable. Maybe the USB cable is bad?
[ 11.822435] input input3: as5013_open
[ 11.831320] Bluetooth: HCI UART driver ver 2.3
[ 11.850253] ehci-omap 4a064c00.ehci: port 2 reset error -110
[ 11.858223] Bluetooth: HCI UART protocol H4 registered
[ 11.873488] Bluetooth: HCI UART protocol BCSP registered
[ 11.897250] Bluetooth: HCI UART protocol LL registered
[ 11.936426] Bluetooth: HCI UART protocol Broadcom registered
[ 11.985681] Bluetooth: hci0: change remote baud rate command in firmware
[ 12.457827] EXT4-fs (mmcblk0p1): warning: mounting unchecked fs, running e2fsck is recommended
[ 12.491042] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null)
[ 12.513064] ext4 filesystem being mounted at /boot supports timestamps until 2038 (0x7fffffff)
[ 12.528357] emif_probe: error getting device data
[ 12.592227] emif_probe: error getting device data
[ 12.724989] emif_probe: error getting device data
[ 12.725039] emif_probe: error getting device data
[ 12.840272] ehci-omap 4a064c00.ehci: port 2 reset error -110
[ 12.947207] asoc-simple-card sound_bluetooth: W2CBW003 <-> 40122000.mcbsp mapping ok
[ 13.112338] dmtimer posted=0
[ 13.135867] dmtimer posted=0
[ 13.176917] asoc-simple-card sound_fmradio: W2CBW003 <-> 40124000.mcbsp mapping ok
[ 13.434939] asoc-simple-card sound_telephony: gtm601 <-> 40126000.mcbsp mapping ok
[ 13.611073] snd_soc_omap_abe_twl6040: unknown parameter 'index' ignored
[ 13.654361] omap-abe-twl6040 sound: ASoC: unknown pin AFML
[ 13.654369] omap-abe-twl6040 sound: ASoC: unknown pin AFMR
[ 13.672030] omap-abe-twl6040 sound: twl6040-legacy <-> 40132000.mcpdm mapping ok
[ 13.675675] input: Letux Cortex 15 Headset Jack as /devices/platform/sound/sound/card4/input10
[ 13.740237] ehci-omap 4a064c00.ehci: port 2 reset error -110
[ 14.244784] wl18xx_driver wl18xx.2.auto: Direct firmware load for ti-connectivity/wl18xx-conf.bin failed with error -2
[ 14.244786] wl18xx_driver wl18xx.2.auto: Falling back to sysfs fallback for: ti-connectivity/wl18xx-conf.bin
[ 14.253144] wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin: -11
[ 14.314151] wlcore: WARNING falling back to default config
[ 14.493075] PVR_K: UM DDK-(3699939) and KM DDK-(3699939) match. [ OK ]
[ 14.620303] ehci-omap 4a064c00.ehci: port 2 reset error -110
[ 14.829993] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)
[ 14.836429] wlcore: WARNING Detected unconfigured mac address in nvs, derive from fuse instead.
[ 14.866296] wlcore: WARNING This default nvs file can be removed from the file system
[ 14.874901] wlcore: loaded
[ 15.500216] ehci-omap 4a064c00.ehci: port 2 reset error -110
[ 15.554416] wwan_on_off_rfkill_set_block: blocked: 0
[ 15.554416] wwan_on_off_set_powern = 1
[ 15.554425] wwan_on_off_is_powered_on: gpio value = 0
[ 15.554431] wwan_on_off_is_powered_on: return 'false'
[ 15.554437] wwan_on_off_set_power: state 0
[ 15.554446] wwan_on_off_set_power: regulator 0
[ 15.761966] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 15.761979] Bluetooth: BNEP socket layer initialized
[ 16.040075] input input2: as5013_open
[ 16.055148] input input3: as5013_open
[ 16.159915] usb usb1-port2: Cannot enable. Maybe the USB cable is bad?
[ 16.159959] usb usb1-port2: attempt power cycle
[ 18.110582] wwan_on_off_set_power: send impulse
[ 18.849124] wwan_on_off_is_powered_on: gpio value = 1
[ 18.854523] wwan_on_off_is_powered_on: return 'true'
[ 18.860881] wwan_on_off_set_power: done
[ 18.865655] wwan_on_off_rfkill_set_block: blocked: 0
[ 18.874225] wwan_on_off_set_powern = 1
[ 18.878513] wwan_on_off_is_powered_on: gpio value = 1
[ 18.884720] wwan_on_off_is_powered_on: return 'true'
[ 18.890581] wwan_on_off_set_power: state 1
[ 18.894981] wwan_on_off_set_power: regulator 1
[ 18.900457] wwan_on_off_set_power: done
[ 18.907699] input: pyraInput keyboard as /devices/virtual/input/input11
[ 18.943972] input: pyraInput Gamepad as /devices/virtual/input/input12
[ 18.969748] input: pyraInput Mouse as /devices/virtual/input/input13
[ 19.932662] wlcore: PHY firmware version: Rev 8.2.0.0.242
[ 20.031771] wlcore: firmware booted (Rev 8.9.0.0.79)
[ 20.052462] wlcore: down
[ 20.490249] wlcore: PHY firmware version: Rev 8.2.0.0.242
[ 20.587283] wlcore: firmware booted (Rev 8.9.0.0.79)
[ 22.713782] fuse: init (API version 7.31)
[ 25.311133] wlcore: down
[ 29.623959] wlan0: authenticate with 34:e3:80:6e:3f:e4
[ 29.642154] wlan0: send auth to 34:e3:80:6e:3f:e4 (try 1/3)
[ 29.671109] wlan0: authenticated
[ 29.688693] wlan0: associate with 34:e3:80:6e:3f:e4 (try 1/3)
[ 29.700228] wlan0: RX AssocResp from 34:e3:80:6e:3f:e4 (capab=0x431 status=0 aid=53)
[ 29.717257] wlan0: associated
[ 30.082945] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 30.104190] wlcore: Association completed.
[ 33.768748] Bluetooth: RFCOMM socket layer initialized
[ 33.774203] Bluetooth: RFCOMM ver 1.11
[ 35.688737] host1_vbus_power: supplied by modem_vbus_hdmi_power
[ 35.708773] host2_vbus_power: supplied by modem_vbus_hdmi_power
[ 35.715791] ldo3: disabling
[ 35.719898] ldo8: disabling
[ 35.728300] otg_path: disabling
[ 37.279111] [UFW BLOCK] IN=wlan0 OUT= MAC=01:00:5e:00:00:01:34:e3:80:6e:3f:e1:08:00 SRC=192.168.1.254 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=50523 PROTO=2
[ 162.172427] [UFW BLOCK] IN=wlan0 OUT= MAC=01:00:5e:00:00:01:34:e3:80:6e:3f:e1:08:00 SRC=192.168.1.254 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=50524 PROTO=2
[ 287.064944] [UFW BLOCK] IN=wlan0 OUT= MAC=01:00:5e:00:00:01:34:e3:80:6e:3f:e1:08:00 SRC=192.168.1.254 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0xC0 TTL=1 ID=50525 PROTO=2

dmesg when usb workes:

Spoiler

[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.6.19-daveiii-pyradef-aufs (pyra@debian-buster) (gcc version 8.3.0 (Debian 8.3.0-2)) #3 SMP PREEMPT Mon Dec 14 18:23:52 CET 2020
[ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache
[ 0.000000] OF: fdt: Machine model: Pyra-Handheld-V5.3
[ 0.000000] printk: debug: ignoring loglevel setting.
[ 0.000000] printk: debug: ignoring loglevel setting.
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 64 MiB at 0x00000000fb000000
[ 0.000000] OMAP4: Map 0x00000000afd00000 to (ptrval) for dram barrier
[ 0.000000] On node 0 totalpages: 1043712
[ 0.000000] DMA zone: 2295 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 195840 pages, LIFO batch:63
[ 0.000000] HighMem zone: 847872 pages, LIFO batch:63
[ 0.000000] OMAP5432 ES2.0
[ 0.000000] percpu: Embedded 20 pages/cpu s50316 r8192 d23412 u81920
[ 0.000000] pcpu-alloc: s50316 r8192 d23412 u81920 alloc=20*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 1041417
[ 0.000000] Kernel command line: root=PARTUUID=947d8093-02 console=ttyO2,115200n8 console=tty0 vram=12M omapfb.vram=0:8M,1:4M omapfb.rotate_type=0 omapdss.def_disp=lcd rootwait twl4030_charger.allow_usb=1 musb_hdrc.preserve_vbus=1 log_buf_len=8M ignore_loglevel earlyprintk drm_kms_helper.fbdev_rotation=8 drm.force_hw_rotation fastboot coherent_pool=1M twl4030_charger.allow_usb=1 fsck.repair=yes rootfstype=f2fs rootwait ignore_loglevel
[ 0.000000] printk: log_buf_len: 8388608 bytes
[ 0.000000] printk: early log buf free: 63724(97%)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stackff, heap allocff, heap freeff
[ 0.000000] software IO TLB: mapped [mem 0xa53bf000-0xa93bf000] (64MB)
[ 0.000000] Memory: 3948468K/4174848K available (10478K kernel code, 908K rwdata, 2772K rodata, 2048K init, 269K bss, 160844K reserved, 65536K cma-reserved, 3325952K highmem)
[ 0.000000] random: get_random_u32 called from __kmem_cache_create+0x34/0x4f8 with crng_init=0
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] OMAP clockevent source: timer1 at 32768 Hz
[ 0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16ac02862, max_idle_ns: 440795202218 ns
[ 0.000010] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511085ns
[ 0.000033] Switching to timer-based delay loop, resolution 162ns
[ 0.000167] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns
[ 0.000183] OMAP clocksource: 32k_counter at 32768 Hz
[ 0.002026] Console: colour dummy device 80x30
[ 0.002987] printk: console [tty0] enabled
[ 0.003058] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.28 BogoMIPS (lpj=61440)
[ 0.003109] pid_max: default: 32768 minimum: 301
[ 0.003398] LSM: Security Framework initializing
[ 0.003531] Yama: becoming mindful.
[ 0.003709] AppArmor: AppArmor initialized
[ 0.003748] TOMOYO Linux initialized
[ 0.003867] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.003913] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.005186] CPU: Testing write buffer coherency: ok
[ 0.005270] CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[ 0.005722] /cpus/cpu@0 missing clock-frequency property
[ 0.005783] /cpus/cpu@1 missing clock-frequency property
[ 0.005817] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.059701] Setting up static identity map for 0x80200000 - 0x80200060
[ 0.079705] rcu: Hierarchical SRCU implementation.
[ 0.119741] smp: Bringing up secondary CPUs ...
[ 0.200083] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.200096] CPU1: Spectre v2: using ICIALLU workaround
[ 0.200228] smp: Brought up 1 node, 2 CPUs
[ 0.200242] SMP: Total of 2 processors activated (24.57 BogoMIPS).
[ 0.200258] CPU: All CPU(s) started in HYP mode.
[ 0.200266] CPU: Virtualization extensions available.
[ 0.200709] devtmpfs: initialized
[ 0.215059] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[ 0.215500] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.215530] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.216858] pinctrl core: initialized pinctrl subsystem
[ 0.217683] thermal_sys: Registered thermal governor 'fair_share'
[ 0.217684] thermal_sys: Registered thermal governor 'step_wise'
[ 0.217696] thermal_sys: Registered thermal governor 'user_space'
[ 0.218569] NET: Registered protocol family 16
[ 0.221129] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.222119] omap_hwmod: l3_main_3 using broken dt data from ocp
[ 0.222933] omap_hwmod: l3_main_2 using broken dt data from ocp
[ 0.236025] audit: initializing netlink subsys (disabled)
[ 0.236238] audit: type=2000 audit(0.230:1): state=initialized audit_enabled=0 res=1
[ 0.239900] cpuidle: using governor menu
[ 0.266195] platform 50000000.gpmc: Cannot lookup hwmod 'gpmc'
[ 0.266390] omap-gpmc 50000000.gpmc: _od_fail_runtime_resume: FIXME: missing hwmod/omap_dev info
[ 0.266414] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[ 0.275090] No ATAGs?
[ 0.275148] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.275180] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.296985] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.303560] vsys_cobra: supplied by vmain
[ 0.307771] iommu: Default domain type: Translated
[ 0.309976] vgaarb: loaded
[ 0.310640] SCSI subsystem initialized
[ 0.311495] libata version 3.00 loaded.
[ 0.311983] usbcore: registered new interface driver usbfs
[ 0.312089] usbcore: registered new interface driver hub
[ 0.312227] usbcore: registered new device driver usb
[ 0.312499] usb_phy_generic hsusb2_phy: hsusb2_phy supply vcc not found, using dummy regulator
[ 0.314302] Advanced Linux Sound Architecture Driver Initialized.
[ 0.314974] NetLabel: Initializing
[ 0.314993] NetLabel: domain hash size = 128
[ 0.315004] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.315065] NetLabel: unlabeled traffic allowed by default
[ 0.315859] clocksource: Switched to clocksource arch_sys_counter
[ 0.382326] VFS: Disk quotas dquot_6.6.0
[ 0.382408] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.383028] AppArmor: AppArmor Filesystem Enabled
[ 0.394869] NET: Registered protocol family 2
[ 0.395368] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.395418] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.395480] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.395632] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.395723] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.395763] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.396011] NET: Registered protocol family 1
[ 0.396456] PCI: CLS 0 bytes, default 64
[ 0.396918] Trying to unpack rootfs image as initramfs...
[ 1.257625] Freeing initrd memory: 18852K
[ 1.258154] hw perfevents: no interrupt-affinity property for /pmu, guessing.
[ 1.258364] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[ 1.260042] Initialise system trusted keyrings
[ 1.260411] workingset: timestamp_bits=14 max_order=20 bucket_order=6
[ 1.268160] zbud: loaded
[ 1.271430] jitterentropy: Initialization failed with host not compliant with requirements: 2
[ 1.271456] Key type asymmetric registered
[ 1.271480] Asymmetric key parser 'x509' registered
[ 1.271517] bounce: pool size: 64 pages
[ 1.271576] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 1.271588] io scheduler mq-deadline registered
[ 1.271608] io scheduler kyber registered
[ 1.276552] OMAP GPIO hardware version 0.1
[ 1.296202] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported)
[ 1.368055] GPIO line 74 (gpio8_234/msecure) hogged as output/high
[ 1.392946] ti-pipe3 4a096000.phy: can't get syscon-pllreset, sata dpll won't idle
[ 1.394289] pinctrl-single 4ae0c840.pinmux: 30 pins, size 60
[ 1.394926] pinctrl-single 4a002840.pinmux: 219 pins, size 438
[ 1.398531] pwm-backlight keyboard-backlight: keyboard-backlight supply power not found, using dummy regulator
[ 1.398813] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[ 1.402984] ti_abb 4ae07cdc.regulator-abb-mpu: can't request region for resource [mem 0x4ae07cdc-0x4ae07ce3]
[ 1.403017] ti_abb: probe of 4ae07cdc.regulator-abb-mpu failed with error -16
[ 1.403078] ti_abb 4ae07ce4.regulator-abb-mm: can't request region for resource [mem 0x4ae07ce4-0x4ae07ceb]
[ 1.403104] ti_abb: probe of 4ae07ce4.regulator-abb-mm failed with error -16
[ 1.403582] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.405484] 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 108, base_baud = 3000000) is a OMAP UART2
[ 2.365163] printk: console [ttyO2] enabled
[ 2.370061] omap_uart 48068000.serial: no wakeirq for uart5
[ 2.376100] 48068000.serial: ttyO5 at MMIO 0x48068000 (irq = 121, base_baud = 3000000) is a OMAP UART5
[ 2.386374] omap_uart 4806c000.serial: no wakeirq for uart1
[ 2.392368] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 122, base_baud = 3000000) is a OMAP UART1
[ 2.402376] serial serial0: tty port ttyO1 registered
[ 2.407867] omap_uart 4806e000.serial: no wakeirq for uart3
[ 2.413851] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 123, base_baud = 3000000) is a OMAP UART3
[ 2.425309] omap_rng 48090000.rng: Random Number Generator ver. 20
[ 2.426048] random: fast init done
[ 2.432458] omapdss_dss 58000000.dss: 58000000.dss supply vdda_video not found, using dummy regulator
[ 2.445246] random: crng init done
[ 2.445375] DSS: OMAP DSS rev 6.1
[ 2.463991] brd: module loaded
[ 2.471310] loop: module loaded
[ 2.474634] wwan_on_off_init: wwan_on_off_init
[ 2.479759] wwan_on_off_probe: wwan_on_off_probe()
[ 2.486772] ahci 4a140000.sata: 4a140000.sata supply ahci not found, using dummy regulator
[ 2.495577] ahci 4a140000.sata: 4a140000.sata supply phy not found, using dummy regulator
[ 2.504335] ahci 4a140000.sata: 4a140000.sata supply target not found, using dummy regulator
[ 2.513460] ahci 4a140000.sata: SSS flag set, parallel bus scan disabled
[ 2.520585] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 2.529634] ahci 4a140000.sata: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part ccc apst
[ 2.540468] scsi host0: ahci
[ 2.543794] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 31
[ 2.552828] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 2.562044] libphy: Fixed MDIO Bus: probed
[ 2.570617] omap-dwc3 4a020000.omap_dwc3: vbus init failed
[ 2.576875] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.583803] ehci-pci: EHCI PCI platform driver
[ 2.588686] usbcore: registered new interface driver usb-storage
[ 2.595777] mousedev: PS/2 mouse device common for all mice
[ 2.603669] i2c /dev entries driver
[ 2.607487] IR NEC protocol handler initialized
[ 2.612294] IR RC5(x/sz) protocol handler initialized
[ 2.617666] IR RC6 protocol handler initialized
[ 2.622456] IR JVC protocol handler initialized
[ 2.627260] IR Sony protocol handler initialized
[ 2.632130] IR SANYO protocol handler initialized
[ 2.637133] IR Sharp protocol handler initialized
[ 2.642109] IR MCE Keyboard/mouse protocol handler initialized
[ 2.648287] IR XMP protocol handler initialized
[ 2.653064] Driver for 1-wire Dallas network protocol.
[ 2.662786] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[ 2.672975] sdhci: Secure Digital Host Controller Interface driver
[ 2.679562] sdhci: Copyright(c) Pierre Ossman
[ 2.685152] omap_gpio 48053000.gpio: Could not set line 4 debounce to 200000 microseconds (-22)
[ 2.694338] omap_hsmmc 4809c000.mmc: Got CD GPIO
[ 2.699252] omap_hsmmc 4809c000.mmc: Got WP GPIO
[ 2.742281] omap_gpio 48057000.gpio: Could not set line 13 debounce to 200000 microseconds (-22)
[ 2.751690] omap_hsmmc 480d1000.mmc: Got CD GPIO
[ 2.756631] omap_hsmmc 480d1000.mmc: Got WP GPIO
[ 2.766274] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.773107] txs02612 txs02612: probe
[ 2.777040] txs02612 txs02612: failed to get mmc phandle in /txs02612 node
[ 2.784334] txs02612 txs02612: could not get access to host port, using manual mode
[ 2.815892] txs02612_request: current=1 client=0
[ 2.845888] txs02612 txs02612: probed
[ 2.849886] txs02612_request: current=0 client=1
[ 2.854799] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.863503] usbcore: registered new interface driver usbhid
[ 2.869478] usbhid: USB HID core driver
[ 2.873742] ashmem: initialized
[ 2.882631] oprofile: using timer interrupt.
[ 2.887266] ata1: SATA link down (SStatus 0 SControl 300)
[ 2.893038] drop_monitor: Initializing network drop monitor service
[ 2.900362] NET: Registered protocol family 10
[ 2.933046] Segment Routing with IPv6
[ 2.936997] mip6: Mobile IPv6
[ 2.940152] NET: Registered protocol family 17
[ 2.944856] mpls_gso: MPLS GSO support
[ 2.949178] ThumbEE CPU extension supported.
[ 2.953703] Registering SWP/SWPB emulation handler
[ 2.958803] omap_vc_init_channel: No PMIC info for vdd_core
[ 2.964681] omap_vp_init: No PMIC info for vdd_core
[ 2.969850] omap_vc_init_channel: No PMIC info for vdd_mm
[ 2.975538] omap_vp_init: No PMIC info for vdd_mm
[ 2.980532] omap_vc_init_channel: No PMIC info for vdd_mpu
[ 2.986330] omap_vp_init: No PMIC info for vdd_mpu
[ 2.991382] Power Management for TI OMAP4+ devices.
[ 2.997142] Loading compiled-in X.509 certificates
[ 3.006166] Loaded X.509 cert 'Build time autogenerated kernel key: 4020818a539cdd7ae890874388bde6caf4fc6257'
[ 3.017132] Key type ._fscrypt registered
[ 3.021382] Key type .fscrypt registered
[ 3.025532] Key type fscrypt-provisioning registered
[ 3.031086] AppArmor: AppArmor sha1 policy hashing enabled
[ 3.058082] dmm 4e000000.dmm: initialized all PAT entries
[ 3.067629] omap-iommu 4a066000.mmu: 4a066000.mmu registered
[ 3.075131] bmc150_accel_i2c 2-0010: mounting matrix not found: using identity...
[ 3.109682] bmc150_accel_i2c 2-0010: Error: Reading chip id
[ 3.115633] bmc150_accel_i2c: probe of 2-0010 failed with error -121
[ 3.122763] bmc150_magn_i2c 2-0012: mounting matrix not found: using identity...
[ 3.130831] bmc150_magn_i2c 2-0012: Failed to bring up device from suspend mode
[ 3.138765] bmc150_magn_i2c: probe of 2-0012 failed with error -121
[ 3.145696] bmp280 2-0077: 2-0077 supply vddd not found, using dummy regulator
[ 3.153414] bmp280 2-0077: 2-0077 supply vdda not found, using dummy regulator
[ 3.172243] bmp280: probe of 2-0077 failed with error -121
[ 3.178358] bmp280 2-0076: 2-0076 supply vddd not found, using dummy regulator
[ 3.186098] bmp280 2-0076: 2-0076 supply vdda not found, using dummy regulator
[ 3.203542] bno055 2-0029: mounting matrix not found: using identity...
[ 3.219362] bno055 2-0029: software revision id 0311
[ 3.226935] input: iio-bridge: bno055 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48060000.target-module/48060000.i2c/i2c-2/2-0029/iio:device1/input/input0
[ 3.246061] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz
[ 3.253084] palmas 0-0048: Irq flag is 0x00000008
[ 3.292604] palmas 0-0048: Muxing GPIO 3, PWM 0, LED 0
[ 3.309511] palmas-rtc 48070000.i2calmas@48:rtc: registered as rtc0
[ 3.322444] SMPS123: supplied by regulator-dummy
[ 3.328863] SMPS45: supplied by regulator-dummy
[ 3.335176] SMPS6: supplied by vsys_cobra
[ 3.340964] SMPS7: supplied by vsys_cobra
[ 3.346543] SMPS8: supplied by vsys_cobra
[ 3.352205] SMPS9: supplied by vsys_cobra
[ 3.356673] smps9: Bringing 0uV into 2100000-2100000uV
[ 3.364407] SMPS10_OUT2: supplied by regulator-dummy
[ 3.371155] SMPS10_OUT1: supplied by regulator-dummy
[ 3.377840] LDO1: supplied by vsys_cobra
[ 3.382234] ldo1: Bringing 0uV into 1800000-1800000uV
[ 3.390008] LDO2: supplied by vsys_cobra
[ 3.394502] ldo2: Bringing 0uV into 1800000-1800000uV
[ 3.404726] ldo4: Bringing 0uV into 1800000-1800000uV
[ 3.412111] LDO5: supplied by vsys_cobra
[ 3.423616] LDO7: supplied by vsys_cobra
[ 3.428255] ldo7: Bringing 0uV into 2000000-2000000uV
[ 3.436311] LDO8: supplied by vsys_cobra
[ 3.442638] LDO9: supplied by vmmcsd_fixed
[ 3.452059] LDOLN: supplied by vsys_cobra
[ 3.458498] LDOUSB: supplied by vsys_cobra
[ 3.466341] palmas_pwrbutton 48070000.i2calmas@48almas_power_button: h/w controlled shutdown duration=8 seconds
[ 3.480322] input: palmas_pwron as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48070000.target-module/48070000.i2c/i2c-0/0-0048/48070000.i2calmas@48almas_power_button/input/input1
[ 3.505636] usb3503 0-0008: usb3503_probe
[ 3.515899] usb3503 0-0008: reset gpio state 1
[ 3.520589] usb3503 0-0008: usb3503_connect
[ 3.525017] usb3503 0-0008: usb3503_reset 1
[ 3.535982] usb3503 0-0008: SP_ILOCK failed (-121)
[ 3.541037] usb3503 0-0008: usb3503_probe: probed in hub mode
[ 3.547398] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz
[ 3.576937] as5013 1-0040: ID code: 0c
[ 3.581545] as5013 1-0040: ID version: 0d
[ 3.586187] as5013 1-0040: silicon revision: 00
[ 3.591616] as5013 1-0040: control: f1
[ 3.595705] input: nub0 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48072000.target-module/48072000.i2c/i2c-1/1-0040/input/input2
[ 3.612317] as5013 1-0040: probe 40, gpio -2, irq 0, "as5013"
[ 3.619173] as5013 1-0041: ID code: 0c
[ 3.623781] as5013 1-0041: ID version: 0d
[ 3.628702] as5013 1-0041: silicon revision: 00
[ 3.634157] as5013 1-0041: control: f1
[ 3.638277] input: nub1 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48072000.target-module/48072000.i2c/i2c-1/1-0041/input/input3
[ 3.654878] as5013 1-0041: probe 41, gpio -2, irq 0, "as5013"
[ 3.663851] input: tca8418 as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48072000.target-module/48072000.i2c/i2c-1/1-0034/input/input4
[ 3.680962] bq27xxx_battery_setup
[ 3.684471] bq27xxx_battery_setup: dm_regs=a4163bd0
[ 3.689980] bq27xxx_battery_settings
[ 3.693788] bq27xxx_battery_set_config
[ 3.697781] bq27xxx_battery_unseal
[ 3.712159] bq27xxx_battery_update_dm_block
[ 3.716645] bq27xxx-battery 1-0055: design-capacity has 6000
[ 3.722615] bq27xxx_battery_update_dm_block
[ 3.727053] bq27xxx-battery 1-0055: design-energy has 22200
[ 3.732923] bq27xxx_battery_update_dm_block
[ 3.737398] bq27xxx-battery 1-0055: terminate-voltage has 3200
[ 3.743543] bq27xxx_battery_seal
[ 3.754408] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz
[ 3.787203] input: TSC2007 Touchscreen as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/4807a000.target-module/4807a000.i2c/i2c-3/3-0048/input/input5
[ 3.806931] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz
[ 3.814485] vdds_1v8_main: supplied by smps7
[ 3.819828] pca953x 4-0022: using AI
[ 3.850796] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz
[ 3.859438] omap-iommu 55082000.mmu: 55082000.mmu registered
[ 3.866749] pwm-backlight keyboard-backlight: keyboard-backlight supply power not found, using dummy regulator
[ 3.877622] dmtimer posted=0
[ 3.880983] pwm-backlight backlight: backlight supply power not found, using dummy regulator
[ 3.890478] ldo4: supplied by vdds_1v8_main
[ 3.901308] wwan_on_off_probe: wwan_on_off_probe()
[ 3.907689] omap-dwc3 4a020000.omap_dwc3: vbus init failed
[ 3.917368] omap_gpio 48053000.gpio: Could not set line 4 debounce to 200000 microseconds (-22)
[ 3.926607] omap_hsmmc 4809c000.mmc: Got CD GPIO
[ 3.931490] omap_hsmmc 4809c000.mmc: Got WP GPIO
[ 3.967815] omap_hsmmc 480ad000.mmc: allocated mmc-pwrseq
[ 4.049349] mmc3: new high speed SDXC card at address aaaa
[ 4.066393] mmcblk3: mmc3:aaaa SF128 119 GiB
[ 4.074162] mmcblk3: p1
[ 4.090620] omap_gpio 48057000.gpio: Could not set line 13 debounce to 200000 microseconds (-22)
[ 4.099947] omap_hsmmc 480d1000.mmc: Got CD GPIO
[ 4.104830] omap_hsmmc 480d1000.mmc: Got WP GPIO
[ 4.116022] omap_hsmmc 480ad000.mmc: card claims to support voltages below defined range
[ 4.142983] mmc4: new high speed SDIO card at address 0001
[ 4.237044] ldo3: supplied by vdds_1v8_main
[ 4.241700] ldo6: supplied by vdds_1v8_main
[ 4.412029] mmc5: new high speed SDXC card at address aaaa
[ 4.429353] mmcblk5: mmc5:aaaa SR64G 59.5 GiB
[ 4.436464] bq2429x_charger 1-006b: bq2429x_parse_dt,line=1539 chg_current = 2048000 usb_input_current = 3000000 adp_input_current = 2048000 bat_volt_max = 4200000
[ 4.451946] mmcblk5: p1
[ 4.455049] bq2429x_charger 1-006b: found regulator-max-microvolt = 4200000
[ 4.465303] vsys: Bringing 3300000uV into 3500000-3500000uV
[ 4.476588] omapdss_dss 58000000.dss: bound 58001000.dispc (ops 0xc0ca350c)
[ 4.484092] omapdss_dss 58000000.dss: bound 58004000.encoder (ops 0xc0ca52d4)
[ 4.492250] omap-hdmi-audio omap-hdmi-audio.1.auto: snd-soc-dummy-dai <-> 58040000.encoder mapping ok
[ 4.502352] omapdss_dss 58000000.dss: bound 58040000.encoder (ops 0xc0ca6160)
[ 4.511812] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 4.518824] [drm] No driver support for vblank timestamp query.
[ 4.558412] drm_setup_crtcs_fb: sw_rotations=1
[ 4.563173] drm_setup_crtcs_fb: fbcon_rotate_hint=0
[ 4.575219] ------------[ cut here ]------------
[ 4.575258] WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x254/0x374
[ 4.575262] 44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4WAKEUP (Idle): Data Access in User mode during Functional access
[ 4.575273] Modules linked in:
[ 4.575289] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.19-daveiii-pyradef-aufs #3
[ 4.575296] Hardware name: Generic OMAP5 (Flattened Device Tree)
[ 4.575336] [<c0212e60>] (unwind_backtrace) from [<c020d1a0>] (show_stack+0x10/0x14)
[ 4.575350] [<c020d1a0>] (show_stack) from [<c0c1b544>] (dump_stack+0x94/0xa8)
[ 4.575380] [<c0c1b544>] (dump_stack) from [<c02351f0>] (__warn+0xd0/0xf8)
[ 4.575404] [<c02351f0>] (__warn) from [<c02355e0>] (warn_slowpath_fmt+0x94/0xb8)
[ 4.575416] [<c02355e0>] (warn_slowpath_fmt) from [<c064c23c>] (l3_interrupt_handler+0x254/0x374)
[ 4.575441] [<c064c23c>] (l3_interrupt_handler) from [<c0290864>] (__handle_irq_event_percpu+0x58/0x29c)
[ 4.575464] [<c0290864>] (__handle_irq_event_percpu) from [<c0290ad4>] (handle_irq_event_percpu+0x2c/0x80)
[ 4.575472] [<c0290ad4>] (handle_irq_event_percpu) from [<c0290b60>] (handle_irq_event+0x38/0x5c)
[ 4.575499] [<c0290b60>] (handle_irq_event) from [<c02950f4>] (handle_fasteoi_irq+0xb8/0x168)
[ 4.575504] [<c02950f4>] (handle_fasteoi_irq) from [<c028fae4>] (generic_handle_irq+0x24/0x34)
[ 4.575533] [<c028fae4>] (generic_handle_irq) from [<c02900b8>] (__handle_domain_irq+0x5c/0xb4)
[ 4.575536] [<c02900b8>] (__handle_domain_irq) from [<c064a570>] (gic_handle_irq+0x3c/0x78)
[ 4.575563] [<c064a570>] (gic_handle_irq) from [<c0201ab8>] (__irq_svc+0x58/0x8c)
[ 4.575563] Exception stack(0xc1201eb8 to 0xc1201f00)
[ 4.575577] 1ea0: 00000000 efc99f80
[ 4.575594] 1ec0: 00000001 c1200000 c120a1c8 c120a158 efc95a78 00000001 00000001 10b3cc6e
[ 4.575596] 1ee0: 00000001 00000001 00000000 c1201f08 c02c13c4 c08ff5c4 20000113 ffffffff
[ 4.575624] [<c0201ab8>] (__irq_svc) from [<c08ff5c4>] (cpuidle_enter_state+0x164/0x5b8)
[ 4.575651] [<c08ff5c4>] (cpuidle_enter_state) from [<c08ffa54>] (cpuidle_enter+0x28/0x38)
[ 4.575661] [<c08ffa54>] (cpuidle_enter) from [<c026781c>] (do_idle+0x234/0x29c)
[ 4.575685] [<c026781c>] (do_idle) from [<c0267b78>] (cpu_startup_entry+0x18/0x20)
[ 4.575708] [<c0267b78>] (cpu_startup_entry) from [<c100137c>] (start_kernel+0x7cc/0x810)
[ 4.575716] [<c100137c>] (start_kernel) from [<00000000>] (0x0)
[ 4.575737] ---[ end trace b49429a4ef83be53 ]---
[ 4.770693] dmtimer posted=0
[ 4.832613] Console: switching to colour frame buffer device 160x45
[ 5.474143] omapdrm omapdrm.0: fb0: omapdrmdrmfb frame buffer device
[ 5.501345] [drm] Initialized omapdrm 1.0.0 20110917 for omapdrm.0 on minor 0
[ 5.516542] wwan_on_off_probe: wwan_on_off_probe()
[ 5.528719] modem_vbus_hdmi_power: supplied by vsys
[ 5.540492] modem_vbus_power: supplied by modem_vbus_hdmi_power
[ 5.553679] wwan_on_off_probe: onoff = 32c76238 indicator = 58894c65 -304231872 usb_phy = -1054427720
[ 5.570284] wwan_on_off_probe: wwan_on_off_probe() wwan=28f85c44
[ 5.583543] wwan_on_off_is_powered_on: gpio value = 0
[ 5.595767] wwan_on_off_is_powered_on: return 'false'
[ 5.607861] wwan_on_off_rfkill_set_block: blocked: 1
[ 5.619480] wwan_on_off_set_powern = 0
[ 5.630007] wwan_on_off_is_powered_on: gpio value = 0
[ 5.641679] wwan_on_off_is_powered_on: return 'false'
[ 5.653261] wwan_on_off_set_power: state 0
[ 5.663704] wwan_on_off_set_power: regulator 0
[ 5.674410] wwan_on_off_set_power: done
[ 5.684380] wwan_on_off_probe: successfully probed
[ 5.695833] otg_path: supplied by otg
[ 5.706216] dwc3 4a030000.dwc3: Failed to get clk 'ref': -2
[ 5.719091] dwc3 4a030000.dwc3: changing max_speed on rev 5533202a
[ 5.733583] input: user-buttons as /devices/platform/user-buttons/input/input6
[ 5.748209] input: pyra-game-buttons as /devices/platform/pyra-game-buttons/input/input7
[ 5.762453] input: pyra-lid-wakeup as /devices/platform/pyra-lid-wakeup/input/input8
[ 5.777130] palmas-rtc 48070000.i2calmas@48:rtc: setting system clock to 2021-06-09T18:53:19 UTC (1623264799)
[ 5.792591] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 5.806520] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 5.818143] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 5.837160] l4sec_cm:clk:0038:0: failed to disable
[ 5.846804] platform regulatory.0: Falling back to sysfs fallback for: regulatory.db
[ 5.846926] ALSA device list:
[ 5.867535] #0: HDMI 58040000.encoder
[ 5.878280] Freeing unused kernel memory: 2048K
[ 5.906530] Run /init as init process
[ 5.936593] with arguments:
[ 5.965456] /init
[ 5.992922] earlyprintk
[ 6.021211] fastboot
[ 6.047945] with environment:
[ 6.075459] HOME=/
[ 6.101900] TERM=linux
[ 6.127840] vram=12M
[ 6.218672] set_switch() to 0
[ 6.566159] drm_setup_crtcs_fb: sw_rotations=1
[ 6.574328] drm_setup_crtcs_fb: fbcon_rotate_hint=0
[ 6.817964] ehci-omap: OMAP-EHCI Host Controller driver
[ 6.859501] mmc0: new high speed MMC card at address 0001
[ 6.886171] mmcblk0: mmc0:0001 HBG4a2 29.1 GiB
[ 6.894747] mmcblk0boot0: mmc0:0001 HBG4a2 partition 1 4.00 MiB
[ 6.916112] mmcblk0boot1: mmc0:0001 HBG4a2 partition 2 4.00 MiB
[ 6.934633] cfg80211: failed to load regulatory.db
[ 6.936067] mmcblk0rpmb: mmc0:0001 HBG4a2 partition 3 4.00 MiB, chardev (245:0)
[ 6.956032] ehci-omap 4a064c00.ehci: EHCI Host Controller
[ 6.967653] mmcblk0: p1 p2
[ 6.975496] etnaviv etnaviv: bound 59000000.bb2d (ops gpu_ops [etnaviv])
[ 6.994264] ehci-omap 4a064c00.ehci: new USB bus registered, assigned bus number 1
[ 7.006532] etnaviv-gpu 59000000.bb2d: model: GC320, revision: 5301
[ 7.017930] ehci-omap 4a064c00.ehci: irq 106, io mem 0x4a064c00
[ 7.028932] [drm] Initialized etnaviv 1.3.0 20151214 for etnaviv on minor 1
[ 7.056098] ehci-omap 4a064c00.ehci: USB 2.0 started, EHCI 1.00
[ 7.068788] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.06
[ 7.081522] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 7.093141] usb usb1: Product: EHCI Host Controller
[ 7.102205] usb usb1: Manufacturer: Linux 5.6.19-daveiii-pyradef-aufs ehci_hcd
[ 7.113588] usb usb1: SerialNumber: 4a064c00.ehci
[ 7.122761] hub 1-0:1.0: USB hub found
[ 7.130434] hub 1-0:1.0: 3 ports detected
[ 7.146927] pvrsrvkm 56000000.gpu: Enabling quirks 00000000
[ 7.169985] [drm] Initialized pvr 1.14.3699939 20110701 for 56000000.gpu on minor 2
[ 7.507082] usb 1-2: new high-speed USB device number 2 using ehci-omap
[ 7.736879] usb 1-2: New USB device found, idVendor=0424, idProduct=3503, bcdDevice=a1.a0
[ 7.769045] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 7.781008] hub 1-2:1.0: USB hub found
[ 7.791753] hub 1-2:1.0: 3 ports detected
[ 8.477388] process '/usr/bin/fstype' started with executable stack
[ 8.591921] F2FS-fs (mmcblk0p2): recover fsync data on readonly fs
[ 8.646364] F2FS-fs (mmcblk0p2): Mounted with checkpoint version = 21555961
[ 8.842836] Not activating Mandatory Access Control as /sbin/tomoyo-init does not exist.
[ 9.182009] systemd[1]: Inserted module 'autofs4'
[ 9.223574] systemd[1]: systemd 241 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 9.262477] systemd[1]: Detected architecture arm.
[ 9.331087] systemd[1]: Set hostname to <terminaalverdwaald>.
[ 9.627382] systemd[1]: File /lib/systemd/system/systemd-journald.service:12 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[ 9.658296] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[ 9.810020] systemd[1]: /lib/systemd/system/dbpd.service:6: PIDFile= references path below legacy directory /var/run/, updating /var/run/dbpd.pid → /run/dbpd.pid; please update the unit file accordingly.
[ 9.878493] systemd[1]: Reached target User and Group Name Lookups.
[ 9.892732] systemd[1]: Listening on Journal Socket (/dev/log).
[ 9.913048] systemd[1]: Listening on RPCbind Server Activation Socket.
[ 9.937593] systemd[1]: Listening on udev Control Socket.
[ 10.216982] RPC: Registered named UNIX socket transport module.
[ 10.216982] RPC: Registered udp transport module.
[ 10.216982] RPC: Registered tcp transport module.
[ 10.216982] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 10.833725] systemd-journald[1857]: Received request to flush runtime journal from PID 1
[ 11.793612] bmg160_i2c 2-0069: mounting matrix not found: using identity...
[ 11.838137] bmg160_i2c 2-0069: Error reading reg_chip_id
[ 11.913446] bmg160_i2c: probe of 2-0069 failed with error -121
[ 11.915599] input: twl6040:vibrator as /devices/platform/44000000.ocp/48000000.interconnect/48000000.interconnect:segment@0/48070000.target-module/48070000.i2c/i2c-0/0-004b/twl6040-vibra/input/input9
[ 12.077638] ina2xx 1-004f: power monitor ina231 (Rshunt = 20000 uOhm)
[ 12.091280] Bluetooth: Core ver 2.22
[ 12.152989] input input2: as5013_open
[ 12.176119] NET: Registered protocol family 31
[ 12.215242] input input3: as5013_open
[ 12.230440] Bluetooth: HCI device and connection manager initialized
[ 12.242930] gpio gpiochip10: (4-0022): gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
[ 12.293672] gpio gpiochip10: (4-0022): unable to lock HW IRQ 14 for IRQ
[ 12.311464] genirq: Failed to request resources for TS3A227E (irq 197) on irqchip 4-0022
[ 12.368990] Bluetooth: HCI socket layer initialized
[ 12.459402] input input3: as5013_open
[ 12.521700] input input2: as5013_open
[ 12.608186] Bluetooth: L2CAP socket layer initialized
[ 12.620758] ts3a227e 4-003b: Cannot request irq 197 (-5)
[ 12.673079] ts3a227e: probe of 4-003b failed with error -5
[ 12.685610] Bluetooth: SCO socket layer initialized
[ 12.841549] Bluetooth: HCI UART driver ver 2.3
[ 12.865975] Bluetooth: HCI UART protocol H4 registered
[ 12.925258] Bluetooth: HCI UART protocol BCSP registered
[ 12.947420] Bluetooth: HCI UART protocol LL registered
[ 13.057195] Bluetooth: hci0: change remote baud rate command in firmware
[ 13.069154] EXT4-fs (mmcblk0p1): warning: mounting unchecked fs, running e2fsck is recommended
[ 13.089998] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null)
[ 13.106172] ext4 filesystem being mounted at /boot supports timestamps until 2038 (0x7fffffff)
[ 13.117464] Bluetooth: HCI UART protocol Broadcom registered
[ 13.396425] emif_probe: error getting device data
[ 13.396481] emif_probe: error getting device data
[ 13.496828] emif_probe: error getting device data
[ 13.497957] emif_probe: error getting device data
[ 14.077700] PVR_K: UM DDK-(3699939) and KM DDK-(3699939) match. [ OK ]
[ 14.279299] asoc-simple-card sound_bluetooth: W2CBW003 <-> 40122000.mcbsp mapping ok
[ 14.729786] snd_soc_omap_abe_twl6040: unknown parameter 'index' ignored
[ 14.754321] asoc-simple-card sound_fmradio: W2CBW003 <-> 40124000.mcbsp mapping ok
[ 14.989441] asoc-simple-card sound_telephony: gtm601 <-> 40126000.mcbsp mapping ok
[ 15.124300] omap-abe-twl6040 sound: ASoC: unknown pin AFML
[ 15.166506] omap-abe-twl6040 sound: ASoC: unknown pin AFMR
[ 15.365511] dmtimer posted=0
[ 15.423802] dmtimer posted=0
[ 15.543428] omap-abe-twl6040 sound: twl6040-legacy <-> 40132000.mcpdm mapping ok
[ 15.606900] input: Letux Cortex 15 Headset Jack as /devices/platform/sound/sound/card4/input10
[ 15.676576] wwan_on_off_rfkill_set_block: blocked: 0
[ 15.676576] wwan_on_off_set_powern = 1
[ 15.676576] wwan_on_off_is_powered_on: gpio value = 0
[ 15.676576] wwan_on_off_is_powered_on: return 'false'
[ 15.676584] wwan_on_off_set_power: state 0
[ 15.676597] wwan_on_off_set_power: regulator 0
[ 15.794100] wl18xx_driver wl18xx.2.auto: Direct firmware load for ti-connectivity/wl18xx-conf.bin failed with error -2
[ 15.794107] wl18xx_driver wl18xx.2.auto: Falling back to sysfs fallback for: ti-connectivity/wl18xx-conf.bin
[ 16.000651] wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin: -11
[ 16.000661] wlcore: WARNING falling back to default config
[ 16.370722] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 16.370729] Bluetooth: BNEP socket layer initialized
[ 16.517214] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)
[ 16.521852] wlcore: WARNING Detected unconfigured mac address in nvs, derive from fuse instead.
[ 16.521852] wlcore: WARNING This default nvs file can be removed from the file system
[ 16.638613] input input2: as5013_open
[ 16.640265] input input3: as5013_open
[ 18.382131] wwan_on_off_set_power: send impulse
[ 19.136259] wwan_on_off_is_powered_on: gpio value = 1
[ 19.141664] wwan_on_off_is_powered_on: return 'true'
[ 19.148249] wwan_on_off_set_power: done
[ 19.154177] wwan_on_off_rfkill_set_block: blocked: 0
[ 19.169124] wwan_on_off_set_powern = 1
[ 19.173372] wwan_on_off_is_powered_on: gpio value = 1
[ 19.181673] wwan_on_off_is_powered_on: return 'true'
[ 19.187677] wwan_on_off_set_power: state 1
[ 19.192110] wwan_on_off_set_power: regulator 1
[ 19.197836] wwan_on_off_set_power: done
[ 19.203890] input: pyraInput keyboard as /devices/virtual/input/input11
[ 19.219574] wlcore: loaded
[ 19.233736] input: pyraInput Gamepad as /devices/virtual/input/input12
[ 19.250735] input: pyraInput Mouse as /devices/virtual/input/input13
[ 20.231430] wlcore: PHY firmware version: Rev 8.2.0.0.242
[ 20.356198] wlcore: firmware booted (Rev 8.9.0.0.79)
[ 20.383927] wlcore: down
[ 20.841991] wlcore: PHY firmware version: Rev 8.2.0.0.242
[ 20.947573] wlcore: firmware booted (Rev 8.9.0.0.79)
[ 22.977144] fuse: init (API version 7.31)
[ 25.591585] wlcore: down
[ 29.953810] wlan0: authenticate with 34:e3:80:6e:3f:e4
[ 29.964144] wlan0: send auth to 34:e3:80:6e:3f:e4 (try 1/3)
[ 29.994234] wlan0: authenticated
[ 30.006166] wlan0: associate with 34:e3:80:6e:3f:e4 (try 1/3)
[ 30.114926] wlan0: RX AssocResp from 34:e3:80:6e:3f:e4 (capab=0x431 status=0 aid=53)
[ 30.143812] wlan0: associated
[ 30.542879] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 30.561556] wlcore: Association completed.
[ 32.416200] usb 1-2.3: new high-speed USB device number 3 using ehci-omap
[ 32.568462] usb 1-2.3: New USB device found, idVendor=1e2d, idProduct=0061, bcdDevice= 2.32
[ 32.577425] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 32.585267] usb 1-2.3: Product: LTE Modem
[ 32.591085] usb 1-2.3: Manufacturer: Cinterion
[ 32.678548] cdc_acm 1-2.3:1.0: ttyACM0: USB ACM device
[ 32.690004] cdc_acm 1-2.3:1.2: ttyACM1: USB ACM device
[ 32.700929] cdc_acm 1-2.3:1.4: ttyACM2: USB ACM device
[ 32.719484] cdc_acm 1-2.3:1.6: ttyACM3: USB ACM device
[ 32.729097] cdc_acm 1-2.3:1.8: ttyACM4: USB ACM device
[ 32.737520] usbcore: registered new interface driver cdc_acm
[ 32.743489] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 32.792574] cdc_ether 1-2.3:1.10 wwan0: register 'cdc_ether' at usb-4a064c00.ehci-2.3, Mobile Broadband Network Device, de:ad:be:ef:00:00
[ 32.809717] cdc_ether 1-2.3:1.12 wwan1: register 'cdc_ether' at usb-4a064c00.ehci-2.3, Mobile Broadband Network Device, de:ad:be:ef:00:01
[ 32.823091] usbcore: registered new interface driver cdc_ether
[ 36.325981] host1_vbus_power: supplied by modem_vbus_hdmi_power
[ 36.334227] host2_vbus_power: supplied by modem_vbus_hdmi_power
[ 36.347505] ldo3: disabling
[ 36.355226] ldo8: disabling
[ 36.359031] otg_path: disabling
[ 36.558720] Bluetooth: RFCOMM socket layer initialized
[ 36.564150] Bluetooth: RFCOMM ver 1.11
[ 53.426210] usb 1-2.1: new high-speed USB device number 4 using ehci-omap
[ 53.615755] usb 1-2.1: New USB device found, idVendor=058f, idProduct=6387, bcdDevice= 1.00
[ 53.624728] usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 53.632692] usb 1-2.1: Product: Mass Storage
[ 53.637392] usb 1-2.1: Manufacturer: Generic
[ 53.641938] usb 1-2.1: SerialNumber: E9031430
[ 53.653658] usb-storage 1-2.1:1.0: USB Mass Storage device detected
[ 53.660738] scsi host1: usb-storage 1-2.1:1.0
[ 54.731332] scsi 1:0:0:0: Direct-Access Generic Flash Disk 8.07 PQ: 0 ANSI: 4
[ 54.746675] sd 1:0:0:0: [sda] 7864320 512-byte logical blocks: (4.03 GB/3.75 GiB)
[ 54.757246] sd 1:0:0:0: [sda] Write Protect is off
[ 54.762300] sd 1:0:0:0: [sda] Mode Sense: 23 00 00 00
[ 54.769075] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 54.788942] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 54.821535] sda: sda1
[ 54.827772] sd 1:0:0:0: [sda] Attached SCSI removable disk

 

[ingoreis]

Okay i can correct me..i tried 5 USB Dongles and all 5 worked.
Dual USB Dram USB Dongle work in all ports from here..even in the OTG Port.

I can say i had that Problem and it is gone.

2 Things i did since last USB Port Testing:
1.) there is a little glossy Paper inside the internal Pyra Micro SD Slot.
I removed that Paper because i tried a Micro SD with Pyra38.img on it.
(i do not think that it helped but maybe you can try to remove that Paper on the Micro Sd Port too)
2.)
I reflashed my Pyra with Pyra38.img

Another Thing is that i installed many Software from the Repo and there was some Dbus Stuff and other Things..maybe something from them helped too.

Tried Fat32,NTFS and ext4 USB Dongle and even with a MicroUSB2 OTG Adapter and a MicroUSB3 OTG Adapter it worked fine.