Search results

Broadcom just open-sourced the 3D driver used for the part in the Raspberry Pi: http://www.raspberrypi.org/archives/2221 Obviously an open-source driver is highly desirable for Pandora 2. Clearly P2 wouldn't use the same hardware as in the Raspberry Pi. But perhaps by then the writing will...

So, this means the replacement cable is from the same manufacturer and batch that the old one was? Meaning that it's kind of likely the same thing will happen again? (And has my fixed Pandora 1ghz already been shipped back to me/)

I didn't put my Pandora in the post to ED until Monday, so, no. ^_^

The cable from my Pandora was sent off to a lab? I feel almost famous!

Notaz: is SuperZaxxon 1.52 sufficient for the 2x renderer, or will that have to wait for yet another kernel?

ED: I could send it directly to you, as I'm in Europe for the next week. I sent you a private message.

The screen on my 1Ghz Pandora is suffering the same fate. It goes way green, flashes horizontal stripes, draws the screen without enough green, and just recently now the screen is mostly completely dead. But... I can get the screen to work at specific hinge angles! Is this possibly a loose...

Another feature request: remember my superweapon choice for the next game, and remember my name for the high score table. You don't have to serialize it and remember it across processes, just remembering it during one run of SGD would be great. Thanks!

I think this is the right one. It should be in "Mystic Marsh" looking at a kinda creepy character. Like the previous poster, I added a ".txt" extension to make the forum software happy.

I don't have a save state for Spyro 1--but I do have a save state for Spyro 2 where the game is already in a very-slowed-down state. It should be 30fps, but it's getting about 10. The music is slow and juddery too; it's XA music, so I'm guessing it's not decoding fast enough and the buffer...

You are right! A quick full reboot and now down is working fine on the right analog stick. Thanks!

Instead of the current totally-symmetric X Y A B button setup, I'd like there to be one obvious default button and have the other three clustered around it. Like the Gamecube controller. There was never any confusion in Gamecube games as to which button you used in the menus, now was there...

I thought PewPew 2 seemed hard for some reason. Finally tried the input tester. The right analog stick can go up, left, and right, all to 32, but it bottoms out at 0 when going down. Since it's exactly precisely zero, I'm betting this is a bad solder or something. (Rather than some physical...

Ah, so then, I was the last one to ship today ;-) Queue position #54, and I ordered three of 'em. (Giving two out as gifts.) I'm in the US, so they won't get here until Wednesday.

So what was the final analysis of the initial four runs of 20? When will the remaining 1ghz units be produced? (Sorry if this has already been discussed, but I've been watching this thread and don't remember seeing answers to these Important Questions.)

Well, if you went public, then you'd sell out much more quickly, and then you could move up the manufacture date and I could get mine sooner. So... do that.

I take it the flux is to help the solder flow down between the tines and the board. Since the button is completely detached right now, what if I applied some solder to the undersides of the tines, then put the button down in the right spot and heated the tines from above? That'd melt the...

My Pandora jumped out of my pocket, fell several feet to the concrete below, and bounced a couple of times. It hit so hard that the SD cards jumped out! The Pandora booted up fine afterwards, but the shoulder buttons were tweaked. I opened it up and discovered the actual hardware buttons...

Has anyone else had luck with sleeping the Pandora with FMN running? Every time I do it, FMN fails to come back on, and it's fullscreen and I can't Alt-Tab away and I wind up holding the power button to reset.

$30 gets you one with a rheostat: http://www.circuitspecialists.com/soldering-stations-csi-station1a.html $50 gets you digital: http://www.circuitspecialists.com/soldering-station-60-watt-3dlf.html I got the rheostat one for myself, and one for my maker-nerd teenage nephew, and have no...