BenScar
What does this do again?
Hello all,
I used to be able to use my break out board, using the files from Art103's site (Thanks!), to read files off my USB drive. Since I've updated to firmware v2 it's stopped working. I've not changed anything on the board itself and the drive hasn't been reformated.
Here's what serial out says as it's actived (USB Host and USB Storage), using the System menu.
(The first is me logging into the telnet)
There is one line "usb.c: USB device 2 (vend/prod 0xdbf/0x300) is not claimed by any active driver." that might be something to do with it (not sure though)
Can anyone tell me what I'm doing wrong?
Thanks in advance!
I used to be able to use my break out board, using the files from Art103's site (Thanks!), to read files off my USB drive. Since I've updated to firmware v2 it's stopped working. I've not changed anything on the board itself and the drive hasn't been reformated.
Here's what serial out says as it's actived (USB Host and USB Storage), using the System menu.
(The first is me logging into the telnet)
There is one line "usb.c: USB device 2 (vend/prod 0xdbf/0x300) is not claimed by any active driver." that might be something to do with it (not sure though)
Code:
login[57]: root login on `pty/s0' from `192.168.1.1'
ttyS1 at MMIO 0xc0001220 (irq =
Using /lib/modules/2.4.25/kernel/drivers/usb/usbcore.o
ttyS2 at MMIO 0xc0001240 (irq = 56) is a MMSP2
usb.c: registered new driver usbdevfs
IRQ_DISP Number = 0
usb.c: registered new driver hublour frame buffer device 40x30
Using /lib/modules/2.4.25/kernel/arch/arm/mach-mmsp2/mmsp2_usbh.oGB0 framebuffer driver start
mmsp2_usbh.c: USB Host power onr driver start
mmsp2_usbh.c: initializing MMSP2 USB host PCI-DMA workaround
MMSP2 DualCPU Interface Driver
Using /lib/modules/2.4.25/kernel/drivers/usb/host/usb-ohci.o
MMSP2 Video Post Processor Dr
usb-ohci.c: USB OHCI at membase 0xf0004300, IRQ 13x76 (Samsung NAND 64MiB 3,3V 8-bit
usb.c: new USB bus registered, assigned bus number 1
)
Creating 5 MTD partitions on "NAND 64
Product: USB OHCI Root Hub
SerialNumber: f00043000000-0x00080000 : "Boo
hub.c: USB hub found
hub.c: 2 ports detected0 : "Param"
kusbd_policy: /sbin/hotplug add 1, ret=0x0 "Kernel"
Using /lib/modules/2.4.25/kernel/drivers/scsi/scsi_mod.o
0x019a0000-0x04000000 : "Extend
NetWinder Floati
Product: USB Storage Adapterle precision)
SerialNumber: 2B04010E08B82D5D
VFS: Mounted root
usb.c: USB device 2 (vend/prod 0xdbf/0x300) is not claimed by any active driver.
Freeing init memory: 280K
MMC/SD
Length = 18
Partition check:
DescriptorType = 01ding data from NAND FLASH
USB version = 2.00d
Vendor:Product = 0dbf:0300
p1
Register SD: 982
MaxPacketSize0 = 64IO charset utf8
NumConfigurations = 1a from NAND FLASH without
Device version = 11.00
Device Class:SubClass:Protocol = 00:00:00booting
Per-interfac
Interface: 0
Alternate Setting: 0
net2272: run
bLength = 9 mode
bDescriptorType = 04: version: 2005 Sept 08
bInterfaceNumber = 00lib/modules/2.4.25/kernel/driv
bAlternateSetting = 00
gs_bind:
bNumEndpoints = 03ized
bInterface Class:SubClass:Protocol = 08:06:50: Gadget Serial v2.0 boundoot.img" from mmc 0:1
iInterface =
bEndpointAddress = 01 (out)t supported` ë » wíÛ¿ïµ½Ÿ the kern
bmAttributes = 02 (Bulk)
rm: cannot remove `/mnt/sd/gp2xboot.
wMaxPacketSize = 0040
bInterval = 00
Memory: 30168KB available (1096
Endpoint:ata, 280K ini
bLength = 7
rm
bDescriptorType = 05el.img': No such file or directo
bEndpointAddress = 82 (in)r /dev
bmAttributes = 02 (Bulk)
wMaxPacketSize = 0040file.img': No such file or direc
bInterval = 00
Endpoint:
,c0385da0)
bLength = 7
INIT: Entering run
bDescriptorType
gw_clos
vhø5 o
hub.c: new USB device <NULL>-2, assigned address 3 reco
usb.c: USB device not accepting new address=3 (error=-110)
h chip found:
hub.c: new USB device <NULL>-2, assigned address 41c77000,c1bfa540) device is no
usb.c: registered new driver usb-storage
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: WDC WD40 Model: 0UE-00HCT0 Rev: 09.0
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
Partition check:
/dev/scsi/host0/bus0/target0/lun0: p1
USB Mass Storage support registered.
SDL_SYS_JoystickInit
Config READ volume : 70
bpp = 16, linelen = 640
0 FBMMSP2CTRL rt msg = 1000, size = 0
prect->xoff = 0
prect->yoff = 0
prect->w = 320
prect->h = 240
graphic device initialize done
screen device open success: pixelvalue = 2
psd->xres = 320, psd->yres = 240, psd->linelen = 320
init draw text context
NOT find resume file
### HERE 1
Can anyone tell me what I'm doing wrong?
Thanks in advance!