Bob Unbricking?

[iluvhockey]

I am trying to unbrick my friends GP2x with the BoB. I can't seem to get the firmware update screen after writing a new image. Here is my output when I run the GP2xRecovery file. Could it be my SD card not being compatible? It is a 2GB ATP Pro Max Super High Speed SD card?

Microsoft Windows XP [Version 5.1.2600]
© Copyright 1985-2001 Microsoft Corp.

D:\GP2X>gp2xrecvoery
'gp2xrecvoery' is not recognized as an internal or external command,
operable program or batch file.

D:\GP2X>gp2xrecovery
JTAGProbe - JTAG interface to the ARM9TDMI/ARM7TDMI
DIGNSYS Inc. (www.dignsys.com)
Modified by Kane. September 2004

Jtag - Using port 0x378
CreateService SUCCESS
failure: StartService (0x02)
Can't get a handle to \\.\giveio
1 file(s) copied.
failure: CreateService, ERROR_SERVICE_EXISTS
StartService SUCCESS
CreateFile SUCCESS
jtag_reset();
JTAG interface reset.
jtag_idcode();
Device ID..0x10920F0F
MMSP2 Detected!
>> Start Flash update <<
1) Initialize...
JTAG interface reset.
2) Halt Device...
Requesting HALT..
System HALTED in 32bit State
R0 is 0x00000020
PC is 0x00000008
3) ID Code Check...
Device ID..0x10920F0F
4) Watch-Dog Disable...
registers read
Poke 0xC0000A14, 0x00000000, 0x00000001
5) Disable Interrupt...
Poke 0xC0000808, 0xFFFFFFFF, 0x00000001
6) Downloading Recovery Image...(SDRAM default base address: 0x3F00000)
Write Block 0x03F00000, length 0x00000400
Write Block 0x03F01000, length 0x00000400
Write Block 0x03F02000, length 0x00000400
Write Block 0x03F03000, length 0x00000400
Write Block 0x03F04000, length 0x00000400
Write Block 0x03F05000, length 0x00000400
Write Block 0x03F06000, length 0x00000400
Write Block 0x03F07000, length 0x00000400
Write Block 0x03F08000, length 0x00000400
Write Block 0x03F09000, length 0x00000400
Write Block 0x03F0A000, length 0x00000400
Write Block 0x03F0B000, length 0x00000400
Write Block 0x03F0C000, length 0x00000400
Write Block 0x03F0D000, length 0x00000400
Write Block 0x03F0E000, length 0x00000400
Write Block 0x03F0F000, length 0x00000400
Write Block 0x03F10000, length 0x00000400
Write Block 0x03F11000, length 0x00000400
Write Block 0x03F12000, length 0x00000400
Write Block 0x03F13000, length 0x00000400
Write Block 0x03F14000, length 0x00000400
Write Block 0x03F15000, length 0x0000013E
7) Please Wait...
Pausing for 0x00000003 seconds
8) Run Image...
registers written
Restarting at 0x03F00000
Done
9) Halt Device...
Requesting HALT..
System HALTED in 32bit State
R0 is 0x00000020
PC is 0x00000008
10) Rerun Image...
Restarting at 0x03F00000
Done
11) Terminate...
ControlService SUCCESS
DeleteService SUCCESS

Is this what I am suppose to see? Any information and poitner would be helpful.

 

[iluvhockey]

All fixed. The instructions were missing a step. You need to type

C:\tmp>instdrv.exe giveio c:\tmp\GIVEIO.SYS

before running

C:\tmp>GP2XRecovery.exe

It just took seconds. Good Luck with those who are also unbricking with the BoB.