Am 16.06.2018 um 13:32 schrieb H. Nikolaus Schaller hns@goldelico.com:
Hi,
Am 15.06.2018 um 23:18 schrieb aTc atc@k-n-p.org:
On 06/15/2018 10:16 PM, H. Nikolaus Schaller wrote:
Am 15.06.2018 um 21:05 schrieb aTc atc@k-n-p.org:
on anything 4.16 the screen just stays blank, and it goes into a loop dumping this sort of stuff:
[ 103.887062] Unhandled fault: synchronous external abort (0x1210) at 0xb5a539f0 [ 103.887066] ------------[ cut here ]------------ [ 103.887099] WARNING: CPU: 0 PID: 0 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x244/0x31c [ 103.894709] pgd = 8c50352e [ 103.899589] 44000000.ocp:L3 Custom Error: MASTER MPU TARGET DMM1 (Read): Data Access in User mode during Functional access [ 103.909217] [b5a539f0] *pgd=a87d7003 [ 103.912070] Modules linked in: [ 103.923714] , *pmd=fc92a003 [ 103.927481] arc4 [ 103.933649] wl18xx wlcore mac80211 cfg80211 dwc3 binfmt_misc leds_gpio wwan_on_off snd_soc_omap_hdmi_audio generic_adc_battery wlcore_sdio snd_soc_ts3a227e leds_is31fl319x bq27xxx_battery_i2c bq2429x_charger bq27xxx_battery ina2xx twl6040_vibra at24 palmas_gpadc usb3503 bmc150_accel_i2c bmc150_magn_i2c w2cbw003_bluetooth bmc150_magn bmg160_i2c bmc150_accel_core bmg160_core industrialio_triggered_buffer kfifo_buf bmp280_i2c bno055 bmp280 snd_soc_omap_mcbsp snd_soc_omap_mcpdm snd_soc_omap snd_pcm_dmaengine ip6t_REJECT nf_reject_ipv6 nf_log_ipv6 xt_hl ip6t_rt nf_conntrack_ipv6 nf_defrag_ipv6 ipt_REJECT nf_reject_ipv4 nf_log_ipv4 nf_log_common xt_LOG xt_limit xt_tcpudp xt_addrtype nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack ip6table_filter ip6_tables nf_conntrack_netbios_ns nf_conntrack_broadcast [ 104.010586] nf_nat_ftp nf_nat nf_conntrack_ftp nf_conntrack iptable_filter ecryptfs encrypted_keys sunrpc ip_tables x_tables ipv6 autofs4 omapdrm drm_kms_helper cfbfillrect syscopyarea cfbimgblt sysfillrect sysimgblt fb_sys_fops cfbcopyarea drm drm_panel_orientation_quirks panel_boe_w677l encoder_tpd12s015 pwm_omap_dmtimer connector_hdmi pwm_bl omapdss omapdss_base cec ehci_omap dwc3_omap tsc2007 industrialio as5013 tca8418_keypad gpio_twl6040 palmas_pwrbutton [ 104.010852] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.16.15-letux-lpae-pyra #1 [ 104.010859] Hardware name: Generic OMAP5 (Flattened Device Tree) [ 104.010895] [<c020e8d0>] (unwind_backtrace) from [<c020ad10>] (show_stack+0x10/0x14) [ 104.010919] [<c020ad10>] (show_stack) from [<c07d3dcc>] (dump_stack+0x7c/0x98) [ 104.010940] [<c07d3dcc>] (dump_stack) from [<c0227c18>] (__warn+0xdc/0xfc) [ 104.010959] [<c0227c18>] (__warn) from [<c0227c6c>] (warn_slowpath_fmt+0x34/0x44) [ 104.010981] [<c0227c6c>] (warn_slowpath_fmt) from [<c0514de0>] (l3_interrupt_handler+0x244/0x31c) [ 104.011007] [<c0514de0>] (l3_interrupt_handler) from [<c026c470>] (__handle_irq_event_percpu+0xb4/0x264) [ 104.011030] [<c026c470>] (__handle_irq_event_percpu) from [<c026c638>] (handle_irq_event_percpu+0x18/0x54) [ 104.011051] [<c026c638>] (handle_irq_event_percpu) from [<c026c6ac>] (handle_irq_event+0x38/0x5c) [ 104.011071] [<c026c6ac>] (handle_irq_event) from [<c026feb4>] (handle_fasteoi_irq+0xb0/0x124) [ 104.011090] [<c026feb4>] (handle_fasteoi_irq) from [<c026b8b8>] (generic_handle_irq+0x18/0x28) [ 104.011111] [<c026b8b8>] (generic_handle_irq) from [<c026be08>] (__handle_domain_irq+0xa0/0xb4) [ 104.011130] [<c026be08>] (__handle_domain_irq) from [<c0512410>] (gic_handle_irq+0x54/0x98) [ 104.011148] [<c0512410>] (gic_handle_irq) from [<c02019f8>] (__irq_svc+0x58/0x8c) [ 104.011157] Exception stack(0xc0c01f08 to 0xc0c01f50) [ 104.011171] 1f00: 00000000 00000018 2e559000 eefccf40 eefcc448 00000000 [ 104.011184] 1f20: 00000000 c0c84c48 30267bbd 00000018 c0c09328 00000000 0000000b c0c01f58 [ 104.011194] 1f40: c069c69c c069c6e4 600f0013 ffffffff [ 104.011215] [<c02019f8>] (__irq_svc) from [<c069c6e4>] (cpuidle_enter_state+0x238/0x390) [ 104.011237] [<c069c6e4>] (cpuidle_enter_state) from [<c02600e8>] (do_idle+0x168/0x1d0) [ 104.011258] [<c02600e8>] (do_idle) from [<c02603bc>] (cpu_startup_entry+0x18/0x1c) [ 104.011282] [<c02603bc>] (cpu_startup_entry) from [<c0a00c18>] (start_kernel+0x360/0x3cc) [ 104.011294] ---[ end trace 2d0dc4badbf61355 ]--- [ 104.283239] wlcore: down [ 104.307175] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 104.433476] wlan0: authenticate with d8:50:e6:cb:03:e0 [ 104.453035] wlan0: send auth to d8:50:e6:cb:03:e0 (try 1/3) [ 104.487453] wlan0: authenticated [ 104.497206] wlan0: associate with d8:50:e6:cb:03:e0 (try 1/3) [ 104.508841] wlan0: RX AssocResp from d8:50:e6:cb:03:e0 (capab=0x411 status=0 aid=2) [ 104.530198] wlan0: associated
is this repeatable on every reboot?
I remember having seen such a thing once but wasn't able to reproduce it.
It might also have something to do with LPAE on a 2GB Pyra, but I am not sure.
I have tried the LPAE kernel build on a 2GB Pyra and can't reproduce your problem yet.
Maybe you can spot some significant difference (warning etc.) before the problem starts?
BR, Nikolaus
U-Boot SPL 2016.11-00241-g0c5e26e (May 13 2017 - 08:28:25) OMAP5432-GP ES2.0
spl:board_init_r()
spl_init() Trying to boot from MMC1 Found LC15 V5.1 board_mmc_init called (vers = 51) MLO hard: gpio7 = eMMC soft: gpio82 = 0 (mmc1=eMMC) ctrl: gpio76 = 1 (ctrl=soft) reading u-boot.img spl: payload image: U-Boot 2016.11-00241-g0c5e26e fo load addr: 0x807fffc0 size: 346760 reading u-boot.img Jumping to U-Boot loaded - jumping to U-Boot...
U-Boot 2016.11-00241-g0c5e26e (May 13 2017 - 08:28:25 +0200)
LPAE build running in hypervisor mode! CPU : ARM Cortex-A15 r2p2 SoC : OMAP5432-GP ES2.0 Board: Pyra with Letux Cortex 15 I2C: ready DRAM: 2 GiB Reset: peripherals tca642x@ 0x22 (24 pins): Bank 0 Configuration: iiiiiiii Polarity: 00000000 Input value: 00100000 Output value: 11111111 Bank 1 Configuration: iiiiiiii Polarity: 00000000 Input value: 01001000 Output value: 11111111 Bank 2 Configuration: iiiiiiii Polarity: 00000000 Input value: 00100010 Output value: 11111111 tca6424 init tca6424 initialized tca642x@ 0x22 (24 pins): Bank 0 Configuration: oooooooo Polarity: 00000000 Input value: 00000000 Output value: 00000000 Bank 1 Configuration: oiooiooo Polarity: 00000000 Input value: 01001000 Output value: 00000000 Bank 2 Configuration: ooooiiii Polarity: 00000000 Input value: 00000010 Output value: 00000000 MMC: Found LC15 V5.1 board_mmc_init called (vers = 51) U-Boot soft: gpio82 = 0 (mmc1=eMMC) OMAP SD/MMC: 0, OMAP SD/MMC: 1, OMAP SD/MMC: 2 *** Warning - bad CRC, using default environment
Found Pyra MB V5.1 Device Tree: omap5-letux-cortex15-v5.1+pyra-v5.1.dtb SCSI: SATA link 0 timeout. AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: 64bit ncq stag pm led clo only pmp pio slum part ccc apst scanning bus for devices... Found 0 device(s). Net: No ethernet found. Hit any key to stop autoboot: 0 Letux OMAP5 bootcmd switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 reading boot.scr ** Unable to read file boot.scr ** reading uEnv.txt 85 bytes read in 3 ms (27.3 KiB/s) Loaded env from uEnv.txt Importing environment from mmc0 ... switch to partitions #0, OK mmc0 is current device SD/MMC found on device 0 reading uEnv.txt 85 bytes read in 3 ms (27.3 KiB/s) Loaded environment from Importing environment from mmc0 ... reading //uImage 4416080 bytes read in 225 ms (18.7 MiB/s) reading //omap5-letux-cortex15-v5.1+pyra-v5.1.dtb 63515 bytes read in 12 ms (5 MiB/s) Booting from mmc0 ... ## Booting kernel from Legacy Image at 82000000 ... Image Name: Linux-4.16.15-letux-lpae+ Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4416016 Bytes = 4.2 MiB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK ## Flattened Device Tree blob at 88000000 Booting using the fdt blob at 0x88000000 Loading Kernel Image ... OK Loading Device Tree to 8ffed000, end 8ffff81a ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.16.15-letux-lpae+ (hns@iMac.fritz.box) (gcc version 4.9.2 (GCC)) #2430 SMP PREEMPT Tue Jun 12 23:51:27 CEST 2018
^^^ this is the binary from http://download.goldelico.com/letux-kernel/latest-lpae/
[ 0.000000] CPU: ARMv7 Processor [412fc0f2] revision 2 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Pyra-Handheld-V5.1 [ 0.000000] debug: ignoring loglevel setting. [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] cma: Reserved 16 MiB at 0x00000000fd800000 [ 0.000000] OMAP4: Map 0x00000000fed00000 to (ptrval) for dram barrier [ 0.000000] On node 0 totalpages: 519424 [ 0.000000] DMA zone: 1536 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 196608 pages, LIFO batch:31 [ 0.000000] HighMem zone: 322816 pages, LIFO batch:31 [ 0.000000] OMAP5432 ES2.0 [ 0.000000] percpu: Embedded 17 pages/cpu @(ptrval) s39680 r8192 d21760 u69632 [ 0.000000] pcpu-alloc: s39680 r8192 d21760 u69632 alloc=17*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 517888 [ 0.000000] Kernel command line: console= root=PARTUUID=7d45bc20-02 rw rootfstype=ext4 rootwait console=ttyO2,115200n8 vram=12M omapfb.vram=0:8M,1:4M omapfb.rotate_type=0 omapdss.def_disp=lcd rootwait twl4030_charger.allow_usb=1 log_buf_len=8M ignore_loglevel earlyprintk [ 0.000000] log_buf_len: 8388608 bytes [ 0.000000] early log buf free: 63968(97%) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 2024620K/2077696K available (6111K kernel code, 567K rwdata, 1640K rodata, 2048K init, 221K bss, 36692K reserved, 16384K cma-reserved, 1274880K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xf0800000 - 0xff800000 ( 240 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf0000000 ( 768 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (8128 kB) [ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (2048 kB) [ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 568 kB) [ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 222 kB) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Tasks RCU enabled. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] OMAP clockevent source: timer1 at 32768 Hz [ 0.000000] arch_timer: cp15 timer(s) running at 6.14MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x16ac02862, max_idle_ns: 440795202218 ns [ 0.000005] sched_clock: 56 bits at 6MHz, resolution 162ns, wraps every 4398046511085ns [ 0.000017] Switching to timer-based delay loop, resolution 162ns [ 0.000313] clocksource: 32k_counter: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 58327039986419 ns [ 0.000322] OMAP clocksource: 32k_counter at 32768 Hz [ 0.001016] Console: colour dummy device 80x30 [ 0.001037] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.28 BogoMIPS (lpj=61440) [ 0.001053] pid_max: default: 32768 minimum: 301 [ 0.001140] Security Framework initialized [ 0.001186] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001199] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.001617] CPU: Testing write buffer coherency: ok [ 0.001802] /cpus/cpu@0 missing clock-frequency property [ 0.001818] /cpus/cpu@1 missing clock-frequency property [ 0.001829] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.039935] Setting up static identity map for 0x80200000 - 0x80200060 [ 0.059939] Hierarchical SRCU implementation. [ 0.099987] smp: Bringing up secondary CPUs ... [ 0.170425] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.170510] smp: Brought up 1 node, 2 CPUs [ 0.170523] SMP: Total of 2 processors activated (24.57 BogoMIPS). [ 0.170531] CPU: All CPU(s) started in HYP mode. [ 0.170537] CPU: Virtualization extensions available. [ 0.170864] devtmpfs: initialized [ 0.180617] random: get_random_u32 called from bucket_table_alloc+0x15c/0x1ac with crng_init=0 [ 0.190339] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0 [ 0.190694] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.190710] futex hash table entries: 512 (order: 3, 32768 bytes) [ 0.191156] pinctrl core: initialized pinctrl subsystem [ 0.191713] NET: Registered protocol family 16 [ 0.193381] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.194046] omap_hwmod: l3_main_3 using broken dt data from ocp [ 0.194659] omap_hwmod: l3_main_2 using broken dt data from ocp [ 0.255303] audit: initializing netlink subsys (disabled) [ 0.255875] audit: type=2000 audit(0.250:1): state=initialized audit_enabled=0 res=1 [ 0.256121] cpuidle: using governor menu [ 0.262183] OMAP GPIO hardware version 0.1 [ 0.265674] GPIO line 234 (gpio8_234/msecure) hogged as output/high [ 0.266016] platform 50000000.gpmc: Cannot lookup hwmod 'gpmc' [ 0.266124] omap-gpmc 50000000.gpmc: _od_fail_runtime_resume: FIXME: missing hwmod/omap_dev info [ 0.266136] omap-gpmc 50000000.gpmc: GPMC revision 6.0 [ 0.279134] No ATAGs? [ 0.279279] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.279292] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.279465] omap4_sram_init:Unable to get sram pool needed to handle errata I688 [ 0.279721] OMAP DMA hardware revision 0.0 [ 0.306137] omap-dma-engine 4a056000.dma-controller: OMAP DMA engine driver (LinkedList1/2/3 supported) [ 0.307444] vsys_cobra: supplied by vmain [ 0.308236] reg-fixed-voltage fixedregulator-mmcsdio: could not find pctldev for node /ocp/l4@4a000000/scm@2800/pinmux@40/pinmux_wlan_pins, deferring probe [ 0.308562] reg-fixed-voltage bt_en: could not find pctldev for node /ocp/l4@4a000000/scm@2800/pinmux@40/pinmux_bt_pins, deferring probe [ 0.312060] omap-iommu 4a066000.mmu: 4a066000.mmu registered [ 0.312314] omap-iommu 55082000.mmu: 55082000.mmu registered [ 0.313903] SCSI subsystem initialized [ 0.314140] libata version 3.00 loaded. [ 0.314540] usbcore: registered new interface driver usbfs [ 0.314621] usbcore: registered new interface driver hub [ 0.314718] usbcore: registered new device driver usb [ 0.314925] usb_phy_generic hsusb2_phy: hsusb2_phy supply vcc not found, using dummy regulator [ 0.315478] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@2800/pinmux@40/pinmux_i2c1_pins, deferring probe [ 0.315515] omap_i2c 48072000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@2800/pinmux@40/pinmux_i2c2_pins, deferring probe [ 0.315545] omap_i2c 48060000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@2800/pinmux@40/pinmux_i2c3_pins, deferring probe [ 0.315574] omap_i2c 4807a000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@2800/pinmux@40/pinmux_i2c4_pins, deferring probe [ 0.315602] omap_i2c 4807c000.i2c: could not find pctldev for node /ocp/l4@4a000000/scm@2800/pinmux@40/pinmux_i2c5_pins, deferring probe [ 0.316342] Advanced Linux Sound Architecture Driver Initialized. [ 0.317386] clocksource: Switched to clocksource arch_sys_counter [ 0.356407] VFS: Disk quotas dquot_6.6.0 [ 0.356470] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.366625] NET: Registered protocol family 2 [ 0.367083] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.367108] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.367179] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.367311] TCP: Hash tables configured (established 8192 bind 8192) [ 0.367431] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.367463] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.367590] NET: Registered protocol family 1 [ 0.419449] hw perfevents: no interrupt-affinity property for /pmu, guessing. [ 0.419614] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available [ 0.423303] Initialise system trusted keyrings [ 0.423407] workingset: timestamp_bits=30 max_order=19 bucket_order=0 [ 0.423691] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.425095] Key type asymmetric registered [ 0.425105] Asymmetric key parser 'x509' registered [ 0.425149] bounce: pool size: 64 pages [ 0.425234] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.425244] io scheduler noop registered [ 0.425252] io scheduler deadline registered [ 0.425287] io scheduler cfq registered (default) [ 0.425295] io scheduler mq-deadline registered [ 0.425303] io scheduler kyber registered [ 0.428546] ti-pipe3 4a096000.phy: can't get syscon-pllreset, sata dpll won't idle [ 0.429305] pinctrl-single 4a002840.pinmux: 219 pins, size 438 [ 0.429761] pinctrl-single 4ae0c840.pinmux: 30 pins, size 60 [ 0.434219] omap_uart 4806c000.serial: no wakeirq for uart1 [ 0.434313] 4806c000.serial: ttyO1 at MMIO 0x4806c000 (irq = 46, base_baud = 3000000) is a OMAP UART1 [ 0.434525] serial serial0: tty port ttyO1 registered [ 0.434792] 48020000.serial: ttyO2 at MMIO 0x48020000 (irq = 47, base_baud = 3000000) is a OMAP UART2 [ 1.355912] console [ttyO2] enabled [ 1.360065] omap_uart 4806e000.serial: no wakeirq for uart3 [ 1.365966] 4806e000.serial: ttyO3 at MMIO 0x4806e000 (irq = 48, base_baud = 3000000) is a OMAP UART3 [ 1.376120] omap_uart 48068000.serial: no wakeirq for uart5 [ 1.382049] 48068000.serial: ttyO5 at MMIO 0x48068000 (irq = 49, base_baud = 3000000) is a OMAP UART5 [ 1.399147] brd: module loaded [ 1.406772] loop: module loaded [ 1.410318] txs_probe() [ 1.412960] txs_probe() initial = 0 [ 1.416607] txs_probe() probed [ 1.421398] ahci 4a140000.sata: SSS flag set, parallel bus scan disabled [ 1.428464] ahci 4a140000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.437416] ahci 4a140000.sata: flags: 64bit ncq sntf stag pm led clo only pmp pio slum part ccc apst [ 1.448000] scsi host0: ahci [ 1.451258] ata1: SATA max UDMA/133 mmio [mem 0x4a140000-0x4a1410ff] port 0x100 irq 77 [ 1.459877] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.467942] libphy: Fixed MDIO Bus: probed [ 1.474015] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.480930] usbcore: registered new interface driver usb-storage [ 1.487425] mousedev: PS/2 mouse device common for all mice [ 1.493910] i2c /dev entries driver [ 1.497657] IR NEC protocol handler initialized [ 1.502403] IR RC5(x/sz) protocol handler initialized [ 1.507715] IR RC6 protocol handler initialized [ 1.512460] IR JVC protocol handler initialized [ 1.517197] IR Sony protocol handler initialized [ 1.522045] IR SANYO protocol handler initialized [ 1.526967] IR Sharp protocol handler initialized [ 1.531901] IR MCE Keyboard/mouse protocol handler initialized [ 1.538017] IR XMP protocol handler initialized [ 1.542756] Driver for 1-wire Dallas network protocol. [ 1.550549] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec [ 1.586066] omap_hsmmc 480d1000.mmc: Got CD GPIO [ 1.590990] omap_hsmmc 480d1000.mmc: Got WP GPIO [ 1.596474] ledtrig-cpu: registered to indicate activity on CPUs [ 1.602944] usbcore: registered new interface driver usbhid [ 1.608817] usbhid: USB HID core driver [ 1.612998] ashmem: initialized [ 1.617663] oprofile: using timer interrupt. [ 1.622364] Initializing XFRM netlink socket [ 1.626893] NET: Registered protocol family 17 [ 1.631625] NET: Registered protocol family 15 [ 1.636338] Key type dns_resolver registered [ 1.641082] omap_vc_init_channel: No PMIC info for vdd_core [ 1.646934] omap_vp_init: No PMIC info for vdd_core [ 1.652085] omap_vc_init_channel: No PMIC info for vdd_mm [ 1.657769] omap_vp_init: No PMIC info for vdd_mm [ 1.662711] omap_vc_init_channel: No PMIC info for vdd_mpu [ 1.668488] omap_vp_init: No PMIC info for vdd_mpu [ 1.673498] Power Management for TI OMAP4+ devices. [ 1.678907] ThumbEE CPU extension supported. [ 1.683407] Registering SWP/SWPB emulation handler [ 1.688812] Loading compiled-in X.509 certificates [ 1.706912] palmas 0-0048: Irq flag is 0x00000000 [ 1.715872] mmc0: new high speed MMC card at address 0001 [ 1.722164] mmcblk0: mmc0:0001 HBG4a2 29.1 GiB [ 1.727312] mmcblk0boot0: mmc0:0001 HBG4a2 partition 1 4.00 MiB [ 1.733976] mmcblk0boot1: mmc0:0001 HBG4a2 partition 2 4.00 MiB [ 1.740425] mmcblk0rpmb: mmc0:0001 HBG4a2 partition 3 4.00 MiB, chardev (248:0) [ 1.750097] mmcblk0: p1 p2 [ 1.754396] palmas 0-0048: Muxing GPIO 3, PWM 0, LED 0 [ 1.766957] palmas-rtc 48070000.i2c:palmas@48:rtc: rtc core: registered 48070000.i2c:palmas@48:rtc as rtc0 [ 1.780353] SMPS123: supplied by regulator-dummy [ 1.786864] SMPS45: supplied by regulator-dummy [ 1.791989] random: fast init done [ 1.795595] ata1: SATA link down (SStatus 0 SControl 300) [ 1.802622] SMPS6: supplied by vsys_cobra [ 1.808414] SMPS7: supplied by vsys_cobra [ 1.814163] SMPS8: supplied by vsys_cobra [ 1.820101] SMPS9: supplied by vsys_cobra [ 1.824646] smps9: Bringing 0uV into 2100000-2100000uV [ 1.831472] SMPS10_OUT2: supplied by regulator-dummy [ 1.838037] SMPS10_OUT1: supplied by regulator-dummy [ 1.844295] LDO1: supplied by vsys_cobra [ 1.848955] ldo1: Bringing 0uV into 1800000-1800000uV [ 1.855711] LDO2: supplied by vsys_cobra [ 1.862828] ldo4: Bringing 0uV into 1800000-1800000uV [ 1.869587] LDO5: supplied by vsys_cobra [ 1.879084] LDO7: supplied by vsys_cobra [ 1.883535] ldo7: Bringing 0uV into 2000000-2000000uV [ 1.890386] LDO8: supplied by vsys_cobra [ 1.896456] LDO9: supplied by vmmcsd_fixed [ 1.903263] LDOLN: supplied by vsys_cobra [ 1.909740] LDOUSB: supplied by vsys_cobra [ 1.922280] omap_i2c 48070000.i2c: bus 0 rev0.12 at 400 kHz [ 1.930027] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz [ 1.937273] omap_i2c 48060000.i2c: bus 2 rev0.12 at 400 kHz [ 1.944432] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz [ 1.951438] vdds_1v8_main: supplied by smps7 [ 1.979934] omap_i2c 4807c000.i2c: bus 4 rev0.12 at 400 kHz [ 2.018565] omap_hsmmc 480ad000.mmc: allocated mmc-pwrseq [ 2.062187] mmc1: host does not support reading read-only switch, assuming write-enable [ 2.073258] mmc1: new high speed SDHC card at address 59b4 [ 2.080916] mmcblk1: mmc1:59b4 USD 7.51 GiB [ 2.087869] mmcblk1: p1 p2 [ 2.152099] omap_hsmmc 480d1000.mmc: Got CD GPIO [ 2.157155] omap_hsmmc 480d1000.mmc: Got WP GPIO [ 2.170166] omap_hsmmc 480ad000.mmc: card claims to support voltages below defined range [ 2.193170] mmc2: new high speed SDIO card at address 0001 [ 2.308433] ldo3: supplied by vdds_1v8_main [ 2.314087] ldo4: supplied by vdds_1v8_main [ 2.319853] ldo6: supplied by vdds_1v8_main [ 2.344237] mmc3: new high speed SDHC card at address 0007 [ 2.351245] mmcblk3: mmc3:0007 SD08G 7.42 GiB [ 2.357731] mmcblk3: p1 p2 [ 2.641801] input: user-button as /devices/platform/user-button/input/input0 [ 2.655838] input: pyra-gpio-keys@1 as /devices/platform/pyra-gpio-keys@1/input/input1 [ 2.667762] input: pyra-gpio-keys@2 as /devices/platform/pyra-gpio-keys@2/input/input2 [ 2.677529] palmas-rtc 48070000.i2c:palmas@48:rtc: setting system clock to 2018-06-16 13:16:47 UTC (1529155007) [ 2.688950] vmmcsdio_fixed: disabling [ 2.692789] bt_power: disabling [ 2.697242] ldo3: disabling [ 2.701236] ldo8: disabling [ 2.704424] ALSA device list: [ 2.707636] No soundcards found. [ 2.742838] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.751712] VFS: Mounted root (ext4 filesystem) on device 179:26. [ 2.769036] devtmpfs: mounted [ 2.773737] Freeing unused kernel memory: 2048K Mount failed for selinuxfs on /sys/fs/selinux: No such file or directory INIT: version 2.88 booting [info] Using makefile-style concurrent boot in runlevel S. [....] Starting the hotplug events dispatcher: udevd[ 3.983663] systemd-udevd[1218]: starting version 215 . ok [....] Synthesizing the initial hotplug events...[ 4.049072] random: udevd: uninitialized urandom read (16 bytes read) [ 4.059736] random: udevd: uninitialized urandom read (16 bytes read) [ okdone. [....] Waiting for /dev to be fully populated...^[[c[ 4.281003] usb3503 0-0008: usb3503_probe [ 4.297588] usb3503 0-0008: reset gpio state 0 [ 4.302265] usb3503 0-0008: usb3503_connect [ 4.306807] palmas_pwrbutton 48070000.i2c:palmas@48:palmas_power_button: h/w controlled shutdown duration=8 seconds [ 4.317924] usb3503 0-0008: usb3503_reset 1 [ 4.323551] input: palmas_pwron as /devices/platform/44000000.ocp/48070000.i2c/i2c-0/0-0048/48070000.i2c:palmas@48:palmas_power_button/input/input3 [ 4.337678] usb3503 0-0008: SP_ILOCK failed (-121) [ 4.345111] twl6040 0-004b: Failed to get supply 'vddvibl': -517 [ 4.345426] usb3503 0-0008: usb3503_probe: probed in hub mode [ 4.357431] twl6040-vibra twl6040-vibra: couldn't get regulators -517 [ 4.357554] bno055 2-0029: software revision id 0311 [ 4.369910] twl6040 0-004b: Failed to get supply 'vddvibl': -517 [ 4.377431] twl6040-vibra twl6040-vibra: couldn't get regulators -517 [ 4.385209] at24 0-0050: 128 byte 24c01 EEPROM, writable, 1 bytes/write [ 4.385800] twl6040 0-004b: Failed to get supply 'vddvibl': -517 [ 4.399021] input: accelerometer-iio-input-bridge as /devices/virtual/input/input4 [ 4.407014] twl6040-vibra twl6040-vibra: couldn't get regulators -517 [ 4.415590] twl6040 0-004b: Failed to get supply 'vddvibl': -517 [ 4.423278] bmp280 2-0077: 2-0077 supply vddd not found, using dummy regulator [ 4.430973] twl6040-vibra twl6040-vibra: couldn't get regulators -517 [ 4.438013] twl6040 0-004b: Failed to get supply 'vddvibl': -517 [ 4.446142] bmp280 2-0077: 2-0077 supply vdda not found, using dummy regulator [ 4.453874] twl6040-vibra twl6040-vibra: couldn't get regulators -517 [ 4.460721] as5013 1-0040: ID code: 0c [ 4.465042] as5013 1-0040: ID version: 0d [ 4.473238] as5013 1-0040: silicon revision: 00 [ 4.480129] bmp280: probe of 2-0077 failed with error -121 [ 4.486142] bmc150_magn_i2c 2-0012: Failed to bring up device from suspend mode [ 4.493866] as5013 1-0040: control: f1 [ 4.494007] bmc150_magn_i2c: probe of 2-0012 failed with error -121 [ 4.497992] input: nub0 as /devices/platform/44000000.ocp/48072000.i2c/i2c-1/1-0040/input/input5 [ 4.518078] as5013 1-0040: probe 40, gpio -2, irq 0, "as5013" [ 4.525201] twl6040 0-004b: Failed to get supply 'vddvibl': -517 [ 4.531887] twl6040-vibra twl6040-vibra: couldn't get regulators -517 [ 4.538799] bmg160_i2c 2-0069: Error reading reg_chip_id [ 4.544429] bmg160_i2c: probe of 2-0069 failed with error -121 [ 4.551610] as5013 1-0041: ID code: 0c [ 4.555784] as5013 1-0041: ID version: 0d [ 4.560064] bmc150_accel_i2c 2-0010: Error: Reading chip id [ 4.560176] input: TSC2007 Touchscreen as /devices/platform/44000000.ocp/4807a000.i2c/i2c-3/3-0048/input/input6 [ 4.565975] bmc150_accel_i2c: probe of 2-0010 failed with error -121 [ 4.583367] as5013 1-0041: silicon revision: 00 [ 4.588668] as5013 1-0041: control: f1 [ 4.594189] input: nub1 as /devices/platform/44000000.ocp/48072000.i2c/i2c-1/1-0041/input/input7 [ 4.603744] bmp280 2-0076: 2-0076 supply vddd not found, using dummy regulator [ 4.612738] twl6040 0-004b: Failed to get supply 'vddvibl': -517 [ 4.619708] twl6040-vibra twl6040-vibra: couldn't get regulators -517 [ 4.629569] bmp280 2-0076: 2-0076 supply vdda not found, using dummy regulator [ 4.635566] as5013 1-0041: probe 41, gpio -2, irq 0, "as5013" [ 4.637509] twl6040 0-004b: Failed to get supply 'vddvibl': -517 [ 4.649611] twl6040-vibra twl6040-vibra: couldn't get regulators -517 [ 4.660018] twl6040 0-004b: Failed to get supply 'vddvibl': -517 [ 4.667266] input: tca8418 as /devices/platform/44000000.ocp/48072000.i2c/i2c-1/1-0034/input/input8 [ 4.677079] twl6040-vibra twl6040-vibra: couldn't get regulators -517 [ 4.684359] twl6040 0-004b: Failed to get supply 'vddvibl': -517 [ 4.686373] ts3a227e 4-003b: Cannot request irq 0 (-22) [ 4.696278] twl6040-vibra twl6040-vibra: couldn't get regulators -517 [ 4.696616] ts3a227e: probe of 4-003b failed with error -22 [ 4.709763] ina2xx 1-004f: power monitor ina231 (Rshunt = 20000 uOhm) [ 4.721170] twl6040 0-004b: Failed to get supply 'vddvibl': -517 [ 4.728358] twl6040-vibra twl6040-vibra: couldn't get regulators -517 [ 4.740315] bq2429x_charger 1-006b: invalid det gpio: -2 [ 4.741415] twl6040 0-004b: Failed to get supply 'vddvibl': -517 [ 4.754724] omap-dwc3 4a020000.omap_dwc3: vbus init failed [ 4.757992] twl6040-vibra twl6040-vibra: couldn't get regulators -517 [ 4.760976] bq24296_get_vsys_voltage(0) [ 4.783540] => 3500000 uV [ 4.787515] bq24296_get_vsys_voltage(0) [ 4.799227] => 3500000 uV [ 4.802741] bq24296_get_otg_voltage(1) [ 4.807580] => 4998000 uV [ 4.811440] bq24296_get_otg_current_limit(1) [ 4.816878] bq24296_get_otg_voltage(1) [ 4.822566] => 4998000 uV [ 4.829112] bq2429x_charger 1-006b: failed to request chg_irq: -22 [ 4.837452] bt_power: supplied by vsys [ 4.837776] input: twl6040:vibrator as /devices/platform/44000000.ocp/48070000.i2c/i2c-0/0-004b/twl6040-vibra/input/input9 [ 4.854784] bq27xxx_battery_setup [ 4.858458] bq27xxx_battery_setup: dm_regs=(ptrval) [ 4.868847] (NULL device *): hwmon: 'bq27421-0' is not a valid name attribute, please fix [ 4.880361] bq27xxx_battery_settings [ 4.886111] bq27xxx_battery_set_config [ 4.897533] bq27xxx_battery_unseal [ 4.911897] bq27xxx_battery_update_dm_block [ 4.920821] bq27xxx-battery 1-0055: design-capacity has 6000 [ 4.930196] bq27xxx_battery_update_dm_block [ 4.934841] bq27xxx-battery 1-0055: design-energy has 22200 [ 4.947116] bq27xxx_battery_update_dm_block [ 4.953167] bq27xxx-battery 1-0055: terminate-voltage has 3200 [ 4.961137] bq27xxx_battery_seal [ 5.076621] ehci-omap: OMAP-EHCI Host Controller driver [ 5.116175] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 5.125507] pwm-backlight keyboard-backlight: keyboard-backlight supply power not found, using dummy regulator [ 5.136936] (NULL device *): hwmon: 'pyra-battery' is not a valid name attribute, please fix [ 5.137196] pwm-backlight backlight: backlight supply power not found, using dummy regulator [ 5.157593] iio_charge:0 [ 5.158574] pwm-backlight keyboard-backlight: keyboard-backlight supply power not found, using dummy regulator [ 5.170774] ehci-omap 4a064c00.ehci: EHCI Host Controller [ 5.192970] ehci-omap 4a064c00.ehci: new USB bus registered, assigned bus number 1 [ 5.209036] ehci-omap 4a064c00.ehci: irq 146, io mem 0x4a064c00 [ 5.218968] wwan_on_off_init: wwan_on_off_init [ 5.227752] wwan_on_off_probe: wwan_on_off_probe() [ 5.232865] wwan_on_off_probe: onoff = 171 indicator = 172 act low: 1 usb_phy = -19 [ 5.243390] omapdss: unknown parameter 'def_disp' ignored [ 5.247058] wwan_on_off_probe: wwan_on_off_probe() wwan=(ptrval) [ 5.249259] ehci-omap 4a064c00.ehci: USB 2.0 started, EHCI 1.00 [ 5.255442] wwan_on_off_is_powered_on: gpio value = 1, inverted=1 [ 5.268063] wwan_on_off_is_powered_on: return 'false' [ 5.274703] wwan_on_off_rfkill_set_block: blocked: 1 [ 5.280315] wwan_on_off_set_power:on = 0 [ 5.284446] wwan_on_off_is_powered_on: gpio value = 1, inverted=1 [ 5.291108] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 5.294029] omapdss_dss 58000000.dss: 58000000.dss supply vdda_video not found, using dummy regulator [ 5.299473] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 5.315607] wwan_on_off_is_powered_on: return 'false' [ 5.321271] wwan_on_off_set_power: state 0 [ 5.326645] usb usb1: Product: EHCI Host Controller [ 5.332839] wwan_on_off_set_power: done [ 5.335621] DSS: OMAP DSS rev 6.1 [ 5.340702] usb usb1: Manufacturer: Linux 4.16.15-letux-lpae+ ehci_hcd [ 5.349029] wwan_on_off_probe: successfully probed [ 5.365322] omapdss_dss 58000000.dss: bound 58001000.dispc (ops dispc_component_ops [omapdss]) [ 5.374466] usb usb1: SerialNumber: 4a064c00.ehci [ 5.374607] tpd12s015 encoder: failed to find video source [ 5.380103] hub 1-0:1.0: USB hub found [ 5.385746] connector-hdmi connector: failed to find video source [ 5.389194] hub 1-0:1.0: 3 ports detected [ 5.400606] tpd12s015 encoder: failed to find video source [ 5.411150] tpd12s015 encoder: failed to find video source [ 5.417258] connector-hdmi connector: failed to find video source [ 5.427875] tpd12s015 encoder: failed to find video source [ 5.437646] omap-abe-twl6040 sound: twl6040-legacy <-> 40132000.mcpdm mapping ok [ 5.446677] omapdss_dss 58000000.dss: bound 58004000.encoder (ops dsi_component_ops [omapdss]) [ 5.485386] omapdss_dss 58000000.dss: bound 58040000.encoder (ops hdmi5_component_ops [omapdss]) [ 5.501673] input: Letux Cortex 15 Headset Jack as /devices/platform/sound/sound/card0/input10 [ 5.511520] connector-hdmi connector: failed to find video source [ 5.652047] dwc3 4a030000.dwc3: changing max_speed on rev 5533202a [ 5.701067] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 5.718999] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 5.727000] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 5.736164] cfg80211: failed to load regulatory.db [ 5.787458] usb 1-2: new high-speed USB device number 2 using ehci-omap [ 5.814444] omap-hdmi-audio omap-hdmi-audio.1.auto: snd-soc-dummy-dai <-> 58040000.encoder mapping ok [ 5.842708] random: crng init done [ 5.957300] dmm 4e000000.dmm: initialized all PAT entries [ 5.968612] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 5.975628] [drm] No driver support for vblank timestamp query. [ 5.987925] usb 1-2: New USB device found, idVendor=0424, idProduct=3503 [ 5.995068] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 6.006146] hub 1-2:1.0: USB hub found [ 6.010434] hub 1-2:1.0: 3 ports detected [ 6.043457] wlcore: ERROR ti-connectivity/wl18xx-conf.bin configuration binary size is wrong, expected 1229 got 1221 [ 6.054951] wlcore: WARNING falling back to default config [ 6.245651] Console: switching to colour frame buffer device 90x80 [ 6.310881] omapdrm omapdrm.0: fb0: omapdrm frame buffer device [ 6.349795] [drm] Initialized omapdrm 1.0.0 20110917 for omapdrm.0 on minor 0 [ 6.463649] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11) [ 6.479150] wlcore: WARNING Detected unconfigured mac address in nvs, derive from fuse instead. [ 6.479150] [ 6.490265] wlcore: WARNING This default nvs file can be removed from the file system [ 6.490265] [ 6.514166] wlcore: loaded done. [ ok ....] Setting parameters of disc: (none). [ ok ....] Activating swap...done. ^[[c[ 8.526172] EXT4-fs (mmcblk1p2): re-mounted. Opts: (null) [....] Checking root file system...fsck from util-linux 2.25.2 e2fsck 1.42.12 (29-Aug-2014) rootfs: clean, 29817/410448 files, 278067/1641586 blocks done. [ 8.913435] EXT4-fs (mmcblk1p2): re-mounted. Opts: errors=remount-ro [ ok ....] Activating lvm and md swap...done. [....] Checking file systems...fsck from util-linux 2.25.2 done. [ ok [[c[....] Cleaning up temporary files... /tmp. [ ok ....] Mounting local filesystems...done. [ ok ] Activating swapfile swap...done. [ ok [[c[....] Cleaning up temporary files.... [ ok ....] Setting kernel variables ...done. ^[[c[ 12.825938] NET: Registered protocol family 10 [ 12.843436] Segment Routing with IPv6 [....] Configuring network interfaces...Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/
Cannot find device "eth0" Bind socket to interface: No such device
If you think you have received this message due to a bug rather than a configuration issue please read the section on submitting bugs on either our web page at www.isc.org or in the README file before submitting a bug. These pages explain the proper process and the information we find helpful for debugging..
exiting. Failed to bring up eth0. Cannot find device "eth1" Failed to bring up eth1. [ 13.442694] using random self ethernet address [ 13.447521] using random host ethernet address [ 13.452308] using host ethernet address: 32:70:05:18:ff:78 [ 13.452368] using self ethernet address: 46:10:3a:b3:af:d9 [ 13.459846] usb0: HOST MAC 32:70:05:18:ff:78 [ 13.473164] usb0: MAC 46:10:3a:b3:af:d9 [ 13.477209] using random self ethernet address [ 13.481959] using random host ethernet address [ 13.486651] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 [ 13.493603] g_ether gadget: g_ether ready [ 13.527460] IPv6: ADDRCONF(NETDEV_UP): usb0: link is not ready Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/
Cannot find device "hso0" Bind socket to interface: No such device
If you think you have received this message due to a bug rather than a configuration issue please read the section on submitting bugs on either our web page at www.isc.org or in the README file before submitting a bug. These pages explain the proper process and the information we find helpful for debugging..
exiting. Failed to bring up hso0. Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/
Cannot find device "usb1" Bind socket to interface: No such device
If you think you have received this message due to a bug rather than a configuration issue please read the section on submitting bugs on either our web page at www.isc.org or in the README file before submitting a bug. These pages explain the proper process and the information we find helpful for debugging..
exiting. Failed to bring up usb1. Internet Systems Consortium DHCP Client 4.3.1 Copyright 2004-2014 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/
Cannot find device "usb2" Bind socket to interface: No such device
If you think you have received this message due to a bug rather than a configuration issue please read the section on submitting bugs on either our web page at www.isc.org or in the README file before submitting a bug. These pages explain the proper process and the information we find helpful for debugging..
exiting. Failed to bring up usb2. done. [ ok ] Cleaning up temporary files.... [ ok ] Setting up ALSA...done. [ ok ] Setting up X socket directories... /tmp/.X11-unix /tmp/.ICE-unix^[[c. INIT: Entering runlevel: 2 [info] Using makefile-style concurrent boot in runlevel 2. [ ok ] Starting enhanced syslogd: rsyslogd. [ ok ....] Loading cpufreq kernel modules...done (none). [ ok ] Starting periodic command scheduler: cron. ^[[c^[[c[ 15.703488] wlcore: PHY firmware version: Rev 8.2.0.0.237 [ ok ] Starting NTP server: ntpd. [ 15.803507] wlcore: firmware booted (Rev 8.9.0.0.70) [ 15.821132] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ ok ....] Starting system message bus: dbus. [ ok ....] CPUFreq Utilities: Setting ondemand CPUFreq governor...CPU0...CPU1...done. [ ok ] Starting bluetooth: bluetoothd. [ ok ....] Setting sysfs variables.... [ 16.188471] Console: switching to colour dummy device 80x30 ^[[c[ 16.205527] Bluetooth: Core ver 2.22 [ 16.214816] NET: Registered protocol family 31 [ 16.219798] Bluetooth: HCI device and connection manager initialized ^[[c[ 16.226669] Bluetooth: HCI socket layer initialized [ 16.232482] Bluetooth: L2CAP socket layer initialized [ 16.237871] Bluetooth: SCO socket layer initialized [ 16.277865] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 16.283689] Bluetooth: BNEP socket layer initialized [ ok ] Starting cgroup management daemon: cgmanager[....] Starting OpenBSD Secure Shell server: sshd. [ ok ....] Starting cgroup management proxy daemon: cgproxy. ^[[c[ 16.793376] dmm 4e000000.dmm: initialized all PAT entries [ 16.801422] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 16.808841] [drm] No driver support for vblank timestamp query. [ 16.853530] Console: switching to colour frame buffer device 160x45 [ 16.881529] omapdrm omapdrm.0: fb0: omapdrm frame buffer device [ 16.941892] [drm] Initialized omapdrm 1.0.0 20110917 for omapdrm.0 on minor 0 [ 17.038253] input: nub0 as /devices/platform/44000000.ocp/48072000.i2c/i2c-1/1-0040/input/input11 [ 17.128295] input: nub1 as /devices/platform/44000000.ocp/48072000.i2c/i2c-1/1-0041/input/input12 [FAIL] Starting ISC DHCP server: dhcpd[....] check syslog for diagnostics. ... failed! failed! ^[[c^[[c[ 18.630723] input input11: as5013_open [ 18.642096] input input12: as5013_open dhcpcd[2255]: version 6.0.5 starting dhcpcd[2255]: wlan0: waiting for carrier dhcpcd[2255]: usb0: waiting for carrier dhcpcd[2255]: wlan0: carrier acquired dhcpcd[2255]: wlan0: carrier lost dhcpcd[2255]: wlan0: waiting for carrier [ 21.909561] wlcore: down dhcpcd[2255]: timed out dhcpcd[2255]: allowing 8 seconds for IPv4LL timeout dhcpcd[2255]: timed out dhcpcd[2255]: forked to background, child pid 2729 [FAIL] startpar: service(s) returned failure: isc-dhcp-server ... failed!
Debian GNU/Linux 8 letux console
letux login: