On Fri, Sep 13, 2019 at 1:46 PM Adam Ford aford173@gmail.com wrote:
On Fri, Sep 13, 2019 at 12:18 PM Daniel Lezcano daniel.lezcano@linaro.org wrote:
On 13/09/2019 18:51, H. Nikolaus Schaller wrote:
[ ... ]
Good news (I think)
With cooling-device = <&cpu 1 2> setup, I was able to ask the max frequency and it returned 600MHz.
# cat /sys/devices/virtual/thermal/thermal_zone0/temp 58500 # cat /sys/devices/system/cpu/cpufreq/policy0/scaling_available_frequencies 300000 600000 800000 # cat /sys/devices/system/cpu/cpufreq/policy0/scaling_m scaling_max_freq scaling_min_freq # cat /sys/devices/system/cpu/cpufreq/policy0/scaling_max_freq 600000
looks good! But we have to understand what the <&cpu 1 2> exactly means...
Hopefully someone reading your RFCv2 can answer...
Daniel,
Thank you for replying.
I may have missed the question :)
These are the states allowed for the cooling device (the one you can see in the /sys/class/thermal/cooling_device0/max_state. As the logic is inverted for cpufreq, that can be confusing.
I think that's what has be confused.
If it was a fan with, let's say 5 speeds, you would use <&fan 0 5>, so when the mitigation begins the cooling device state is 0 and then the thermal governor increase the state until it sees a cooling effect.
If <&fan 0 2> is set, the governor won't set a state above 2 even if the temperature increases.
I am not sure I know what you mean by 'state' in this context.
When the cooling driver is able to return the number of states it supports, it is safe to set the states to THERMAL_NO_LIMIT and let the governor to find the balance point.
If the cooling driver is using cpufreq, is the number of supported states equal to the number of operating points given to cpufreq?
Now if the cooling device is cpufreq, the state order is inverted, because the cooling effects happens when decreasing the OPP.
If the boards support 7 OPPs, the state 0 is 7 - 0, so no mitigation, if the state is 1, the cpufreq is throttle to the 6th OPP, 2 to the 5th OPP etc.
I am not sure how the state would be set to 2.
Now the different combinations:
<&cpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT> the governor will use the state 0 to 7.
<&cpu THERMAL_NO_LIMIT 2> the governor will use the state 0 to 2
What would be the difference between <&cpu THERMAL_NO_LIMIT 2> and <&cpu 0 2> ? (if there is any)
<&cpu 1 2> the governor will use the state 1 and 2. That means there is always the cooling effect as the governor won't set it to zero thus stopping the mitigation.
For the purposes of the board in question, we have 4 operating points, 300MHz, 600MHz, 800MHz and 1GHz. Once the board reaches 90C, we need them to cease operation at 800MHz and 1GHz and only permit operation at 300MHz and 600MHz. I am going under the assumption that the cpu index[0] would be for 300MHz, index[1] = 600MHz, etc.
If I am interpreting your comment correctly, I should set <&cpu THERMAL_NO_LIMIT 2> which would allow it to either not cool and run up to 600MHz and not exceed, is that correct?
Does it clarify the DT spec?
I think your reply to my inquiry might. If possible, it would be nice to get this documented into the bindings doc for others in the future. I can do it, but someone with a better understanding of the concept maybe more qualified. I can totally understand why some may want to integrate this into their SoC device trees to slow the processor when hot.
Thank you for taking the time to review this. I appreciate it.
adam
What happens with trip point 60000? (unfortunately one has to reboot in between or can you kexec between two kernel/dtb versions?)
I set the trip point just above the ambient temp. I then tried to run some benchmarks in the background while constantly polling the max frequency and it changes, but it needs to skip the 800MHz point and jump right to the 600 MHz point (or lower)
# cat /sys/devices/system/cpu/cpufreq/policy0/scaling_max_freq 800000
# cat /sys/devices/system/cpu/cpufreq/policy0/scaling_max_freq 600000
Loops: 80000, Iterations: 1, Duration: 12 sec. C Converted Double Precision Whetstones: 666.7 MIPS # cat /sys/devices/system/cpu/cpufreq/policy0/scaling_max_freq 800000
[1]+ Done whetstone 80000
# cat /sys/devices/system/cpu/cpufreq/policy0/scaling_max_freq 800000
# cat /sys/devices/system/cpu/cpufreq/policy0/scaling_max_freq 1000000
BR, Nikolaus
-- http://www.linaro.org/ Linaro.org │ Open source software for ARM SoCs
Follow Linaro: http://www.facebook.com/pages/Linaro Facebook | http://twitter.com/#!/linaroorg Twitter | http://www.linaro.org/linaro-blog/ Blog